Inhaltsverzeichnis
Werbung
1.-
A
Velocità Snelheid Absaugleistung Скорость Velocidade Hastighet
Speed
Vitesse
Velocidad
I
Low
Moyenne
Baja
II
High
Maximum
Alta
+
Intensive
Intensive
Intensiva
Light
Lumière
Luz
On
Allumé
Encendido
Off
Eteint
Apagado
2.-
T
Downloaded from
www.Manualslib.com
C
Низкая
Bassa
Laag
Leistungsstufe
Высокая
Alta
Hoog
Intensivstufe
Интенсивная
Intensa
Intensief
Intensiv
Освещение
Luce
Licht
Beleuchtung
Включено
Accesa
Aan
Ein
Отключено
Spenta
Uit
Aus
manuals search engine
Instructions for use
By pushing buttons shown in the figure 1,
you will be able to control the functions of the
extractor
Two
achieve
recommend switching on the extractor a few
minutes before starting to cook (3 - 5
minutes) so that the air flow is continuous
and stable when extracting the fumes.
Likewise, keep the extractor switched on for
E
a few minutes when cooking is complete to
allow all fumes and odours to be expelled.
D
Cleaning and maintenance
Before
carrying
maintenance activities, ensure that the
A
extractor is disconnected from the mains.
To carry out cleaning and maintenance,
B
follow the Safety Instructions.
There is a fire risk if cleaning is not carried
out in accordance with the instructions.
Filter cleaning
To remove the filters from their locations
Baixa
Låg
release the anchoring points. Clean the filter,
Alta
Hög
either by putting it in the dishwasher (see
notes) or leaving it standing in hot water to
Intensiva
Intensiv
simplify the removal of grease or, if wished,
Luz
Lampa
by means of special sprays (protecting the
Acesa
På
non metallic parts). Once clean, leave it to
Desligada
Av
dry.
Notes: cleaning in the dishwasher with
aggressive detergents may
surface of
affecting its gas retaining properties.
N.B. The filter must be cleaned at least once
a month depending on how often the
extractor is used. It must be remembered
that grease accumulates in the extractor
when cooking, whether it is switched on or
not.
Cleaning of the extractor body
The use of warm (40ºC approx.) soapy water
is recommended. A cloth moistened in this
water is used for cleaning the extractor,
paying
special
Afterwards, dry it using a lint-free cloth.
Note:
* Never use metallic scouring pads or
abrasive products that could damage the
surface.
* Do not use scrapers with metallic surfaces
such as knives, scissors etc.
better
extraction,
we
Active charcoal filter
* To
necessary to firstly remove the metallic
grease filters.
* In order to fix them it is necessary to
introduce the rear lips of each filter in the
holes provided for it in the security grid,
turning them upwards until its fixation by
clipping in the front part (Fig.6).
* The carbon filters last from three to six
months
out
any
cleaning
or
conditions of use.
* The active carbon filters can neither be
washed nor regenerated. Once they are
exhausted, they must be changed.
* To replace worn out filters with new ones,
remove the old ones in the reverse order
to that of installation
Changing Bulbs
* It
disconnected, and ensure the bulbs that
are to be replaced are not hot.
* Remove the light lens to expose the
extractable lamps.
* The maximum bulbs power is 20W.
Dimensions
darken the
metallic
parts, without
this
Electrical characteristics:
REFER TO RATING PLATE
attention
to
the
grids.
install
the
charcoal
filters
it
is
depending
on
the
particular
.
is
important
that
the mains
are
Technical Information
(Fig.3)
Width = 600//900 mm
Depth = 300 mm
Height = 353 mm
Werbung
Inhaltsverzeichnis
