Smeg KSEV 910 X1 Montageanweisung Und Gebrauchsanweisung Seite 21

Functioning - Model with display
A B C
A. OFF key (Display off) /Stand-by (led lit on the display) –
press for a long time to select the function desired.
B. Lighting, on/off.
C. Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the
cooker hood for a established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D. Display showing:
• Fan speed (1-3-P).
• Change grease filters (grease filter saturation indicator
- F)
After washing the anti-grease filter, depress knob A
for about 3 seconds. The letter F will disappear from
the display.
• Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob A for
about 3 seconds. The letter C will disappear from the
display.
• When the led in the lower right side is on, it indicates
that the cooker hood is ready for operation ("standby"
position), the flashing LED indicates that the timer has
been activated for selected speed.
Attention! The active carbon filter saturation indicator is
normally deactivated, to activate it:
Set the hood on OFF (display off), press keys C and G
contemporaneously for 3 secs.
Initially, only letter F will fbe displayed, then after the 3
seconds have passed, letter C will be displayed as well,
indicating that the carbon filter saturation control system is
active.
To switch off the system, re-press the same two buttons:
letter C appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E. Knob to decrease the speed.
F. Knob to increase the speed.
G. Timed intensive speed button: the hood operates at this
speed for 5 minutes and than returns to the previus
settings. The display will show P and a blinking dot. This
function can be cancelled by pressing button A.
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning! Always press the fan off button A before
disconnecting the hood from the mains supply.
D E F
Functioning - Model with display
A
G
A - Lighting, on/off.
B - Fan off (Stand by)
C - Timer for selected speed (visualizes the speed selected
and flashing LED on the lower side of the display).
This knob permits the operation of the cooker hood for a
established period:
20 minutes if the speed selected is 1
15 minutes if the speed selected is 2
10 minutes if the speed selected is 3
5 minutes if the intensive speed P is selected.
D - Display showing:
•
•
•
•
Warning!
The active carbon filter saturation function is not activated.
In order to activate the carbon filter saturation indicator,
press buttons E and F simultaneously for 3 seconds.
Initially, only letter F will fbe displayed, then after the 3
seconds have passed, letter C will be displayed as well,
indicating that the carbon filter saturation control system is
active.
To switch off the system, re-press the same two buttons:
letter C appear on display and after 3 seconds letter it
disappear and the device will be switched off.
E - Knob to decrease the speed: from intensive speed P to
speed level 1.
F - Knob to increase (standby) speed to intensive speed P.
Attention! Intensive speed P has a duration of 5 minutes
after which the cooker hood automatically sets the speed
to level 2 (suction power).
If the hood fails to operate correctly, briefly disconnect it from
the mains power supply for almost 5 sec. by pulling out the
plug. Then plug it in again and try once more before
contacting the Technical Assistance Service.
Warning!
Always press the fan off button A before disconnecting the
hood from the mains supply.
21
B C D
Fan speed (1-3-P).
Change grease filters (grease filter saturation
indicator - F)
After washing the anti-grease filter, depress knob
B for about 3 seconds. The letter F will disappear
from the display.
Change activated carbon filters (carbon filter
saturation indicator - C).
After replacing the charcoal filter, depress knob B
for about 3 seconds. The letter C will disappear from
the display.
When the led in the lower right side is on,
indicates that the cooker hood is ready for operation
("standby" position), the flashing LED indicates that
the timer has been activated for selected speed.
E F
it