Special Safety Instructions - Scheppach PL75 Originalbetriebsanleitung

8. Safety instructions for inserted circu-
lar saw use
a) Each time before you use the saw, make sure that
the protective covering closes. Do not use the saw if
the protective covering cannot move freely and does
not close immediately. Never clip or tie the protective
covering in an opened position. If the saw should ac-
cidentally fall to the ground, the protective covering
can get bent.
Make sure that the protective covering can move free-
ly and does not touch the saw blade or other parts in
all cutting positions.
b) Check the condition and function of the spring for the
protective covering. Have the saw repaired before
use if the protective covering and spring do not work
perfectly. Damaged parts, sticky residuals or piles of
saw dust can interfere with the working of the lower
protective cover.
c) When making an "inserted cut" that does not de-
scribe a right angle, make sure that the saw is guard-
ed against slipping to the side. Slippage can lead to
a saw blade jam and a kickback.
d) Do not put the saw on the workbench or the floor
without making sure that the protective cover is over
the saw blade. An unprotected, running saw blade
can move the saw against the cutting direction and
saw what is in the way. Check the delay time of the
saw.
9. Additional safety instructions for all
sawing with a wedge
a) Use the right wedge for the saw blade that is in use.
The wedge must be thicker than the thickness of the
steel blade but thinner than the width of the teeth.
b) Adjust the wedge as described in the operating in-
structions. Incorrect thickness, position or direction
can be the reason that the wedge does not effectively
prevent a kickback.
c) Always use a wedge, except when making an insert-
ed cut. Reassemble the wedge after an inserted cut.
The wedge is in the way when making an inserted cut
and can cause a kickback.
d) In order for the wedge to be effective, it must be in
the sawing gap. For short cuts, a wedge does not
work to prevent kickbacks.
e) Never run the saw with a bent wedge. Even the small-
est defect can slow down the closing of the protec-
tive cover.
INSTRUCTIONS FOR ALL SAWS
• Do not use a sanding belt.
• Make sure that the wedge is adjusted so that the dis-
tance to the sprocket ring of the saw blade is not
more than 5 mm and that the sprocket ring does not
stick out more than 5 mm above the lower edge of
the wedge.
• Make sure that the dust catching mechanism is cor-
rectly installed, as is described in this manual.
18 GB
• Wear breathing protection.
• Only those saw blades recommended in the manual
should be used.
• Always wear ear protection.
• Replace the saw blades as described in this manual.
• The maximum cut depth is 75 mm.
If the electrical cable of this tool is damaged it must be
replaced by the manufacturer or the customer service
department or a similarly qualified specialist in order to
avoid dangers.
FURTHER SPECIAL SAFETY INSTRUCTIONS FOR
CIRCULAR SAWS
a) Only use the recommended saw blades which cor-
respond to EN 847-1.
b) Do not use sanding belts.
c) Only use the manufacturer's original saw.
Do not use any saw blades which do not correspond
to the characteristics described in these operating in-
structions. Saw blades may not be brought to a stop by
pressure on the machine from the side.
Make sure that the saw blade is tightly assembled and
turns in the correct direction.

10. Special Safety Instructions

Safety instructions for circular saws
- Hold the equipment on the insulated handles, when you
undertake work in which the tool being used could come
into contact with hidden electrical wires, or its own ca-
ble. Contact with a live power source can electrify the
metal parts of the tool and lead to an electrical shock.
11. Technical data
Dimensions
L x W x H mm
Saw blade ø mm / number of
teeth
Thickness of saw blade
Idling speed n
0
Mitre square
Depth of cut 90° mm
Depth of cut 45° mm
Weightkg
Motor V/Hz
Input W
Protection class
Sound pressure level
Sound power level
Typical weighted vibrations
Subject to technical modifications!
420x300x235
210 / 36
1,6
4500
0°-45°
75
55
6,9
230 / 50
1600
II
95 dB(A),
K : 3 dB (A)
pA
106 dB(A),
K : 3 dB (A)
wA
a 5,72 m/s
2
h:
K: 1,5 m/s
2