Cassette Deck - Grundig M 19-C Bedienungsanleitung

Allgemeiner Teil / General Section
Fast Forward/Rewinding
1 You can rewind or fast forward the tape by
pressing S or T on the set or on the
remote control respectively.
2 These controls function independent of the
playback direction that was chosen.
3 Press 9 (or STOP/CLEAR on the remote
control) to stop fast forwarding or rewinding.
Recording from other sources
(TAPE DECK B)
1 Load a blank cassette into TAPE B.
2 Press TAPE to select TAPE B.
3 Press AUTO REV. to select the play mode
( å or ∂ ).
4 Press CD, TUNER or AUX.
5 Press RECORD on the set or on the remote
control for at least one second to start
recording.
– "RECORD" scrolls on the display and the
flag appears.
RECORD
• Press PAUSE ; on the set or on the remote
control to interrupt the recording.
• Press PAUSE ; again to resume the
recording.
6 Press 9 to stop recording.
– "REC STOP" scrolls on the display
Note :
1 Only å or ∂ mode is available during
recording.
2 For CD recording see CD Synchro-start
recording under Compact Disc section.
3 During recording, it is not possible to listen to
another sound source.
Warning!
1 This set is designed for conventional CDs. Do
not use any accessories like disc stabilizer
rings or CD treatment sheets, etc, which may
damage the CD mechanism.
2 Do not load more than one disc into each
tray.
3 When the CD changer is loaded with CD(s),
do not turn over or shake the unit as this may
jam the changer mechanism.
You can load up to three discs in the CD
changer for continuous play without interruption.
In addition to the conventional 12-cm disc, 8-cm
discs can also be used without an adaptor .
Loading the CD Changer
1 Press CD to select CD
2 Press OPEN/CLOSE.
– The CD compartment slides out.
3 Load a disc with the printed side up in the
right tray.
• You can load another disc in the left tray.
• To load the third disc, press the DISC button.
– The CD changer carousel will rotate until the
empty tray is at the right hand side and is
ready for loading.
– Playback will always start with the outer right
disc tray.
4 Press OPEN/CLOSE to close the CD tray.
– The total number of tracks and playing time of
the last selected disc appear on the display.
The following display indications will help you to
know whether the disc trays are empty or loaded.
– indicates the disc tray is empty.
– indicates the disc tray is loaded with a disc.
1
– indicates the current or selected disc tray.
1
1 - 12

CASSETTE DECK

DECK A
T A P E
å
105 340 1K 3K 10K Hz
DECK A B
RECORD
H S D U B
∂
105 340 1K 3K 10K Hz
3 4 5 6 7
9 10 11
2
DECK B
1 3
RECORD
3 4 0 0
∂
105 340 1K 3K 10K Hz
1 2 3 4 5 6 7 8
9 10 11
2
DECK B
3
1
RECORD
R E C S T O P
∂
105 340 1K 3K 10K Hz
CD CHANGER
1 2 3 4
9 10 11
2
1 3
1 0 1 5
105 340 1K 3K 10K Hz
DISC DISC 1 DISC 2 DISC 3 OPEN/CLOSE
CD CHANGER
VOLUME
ON / OFF y
3 CD CHANGER
DIRECT DISC SELECT SYSTEM
2
3
1
CD CHANGER
R D S
M29-C
COMPACT HIFI SYSTEM
D IGITAL S OUND C ONTROL
SEARCH
PRESET EQ
DUBBING SPEED
BAND
HIGH NORMAL RECORD
CD TAPE TUNER AUX
3 4 5 6 7
9 10 11
2
1 3
3 2 1 0
105 340 1K 3K 10K Hz
3 4 5 6
9 10 11
2
1 3
3 - 2 0 0
105 340 1K 3K 10K Hz
3 4
9 10 11
2
3
1
8 - 4 2 0 7
105 340 1K 3K 10K Hz
Dubbing cassettes
(from TAPE DECK A to TAPE DECK B)
1 Load the pre-recorded cassette into TAPE A
and a blank cassette into TAPE B.
– Make sure that both cassettes have their full
spools to the left.
3 Press NORMAL or HIGH SPEED DUBBING to
select the respective dubbing speed mode.
– DUBBING (normal speed) or HS DUB (high
speed) appears on the display and the
flag appears.
RECORD
5 Press 9 to stop dubbing.
Notes :
– Dubbing of cassettes is only possible in the
TAPE mode. To ensure good dubbing, use
tapes of the same length.
8
– During high speed dubbing in Tape mode,
the sound is completely muted.
Playing a Disc
1 Press B on the unit or on the remote control
to start playback.
– 'CD PLAY' scrolls across the display.
– The selected disc tray blinks and the playing
5 6 7 8
track flashes in the calendar.
– The track number and elapsed playing time
of the current track appear on the display.
• To interrupt play, press PAUSE ; (or PAUSE
on the remote control).
– 'CD PAUSE' scrolls across the display.
– The playing time flashes.
• To resume play, press B or PAUSE ; again.
2 To stop play, press 9 (or STOP/CLEAR on the
remote control).
Note : All the available discs will play once,
then stop.
When the CD tray is closed, you can play a CD
directly by pressing the DISC (1 ~ 3) buttons.
Changing the display mode
during playback
You can change to a different type of time
display when the CD is playing.
8
• Press RDS (or RDS/CD TIME on the remote
control) to cycle through the various time
display modes.
7 8
– The display will show :
Elapsed playing time of the current track –>
Remaining playing time of the current track
–> Remaining playing time of CD –> ...
5 6 7 8
M 19-C / M 29-C
GRUNDIG Service