Grundig M 19-C Bedienungsanleitung Seite 11

M 19-C / M 29-C
Tuning to radio stations
1 Press TUNER ( BAND ) on the unit or on the
remote control.
– First TUNER scrolls once on the display and
after a few seconds it will show the current
frequency or the station name if available.
2 Press TUNER again to select the desired
waveband: FM, MW or LW.
3 Press TUNING S or T for more than
one second.
– The display will search the frequency until a
station with sufficient signal strength is found.
– The or
STEREO TUNED TUNED
• Repeat this procedure until the desired station
is reached.
• To tune to a weak station, briefly press
TUNING S or T until the display shows
the right frequency and/or when the best
reception has been obtained.
• When tuning to a station in FM, the unit
always selects FM STEREO. If stereo reception
is disturbed you can press FM ST on the remote
control to select FM MONO.
Receiving RDS radio stations
RDS (Radio Data System) is a broadcasting
service that allows FM stations to send additional
information along with the regular FM radio
signal.
This additional information can contain:
• STATION NAME : The station name is
displayed.
• PROGRAM TYPE (PTY): The following
program types exist and can be received by
your tuner: News, Affairs, Info, Sport,
Educate, Drama, Culture, Science, Varied,
Pop M, Rock M, M.O.R. (middle of the road
music), Light M, Classics, Other M.
• RADIO TEXT (RT) : Text messages appear in
the display.
• FREQUENCY : The frequency of the station is
displayed.
When you have tuned to an RDS station, the
RDS logo ( Ç ) and the station name will appear
on the display:
• The display normally shows the radio station
name if available.
By repeatedly pressing RDS (or RDS/CD TIME
on the remote control) you can change the
type of display information:
– The display shows in turn: STATION NAME
-> PROGRAM TYPE -> RADIO TEXT ->
FREQUENCY -> STATION NAME ...
Notes :
1 When you press RDS (or RDS/CD TIME on
the remote control) and the display shows
"NO PS", it indicates that either the tuned
station is not transmitting RDS signal or it is a
non RDS station.
2 When no program type is transmitted by the
radio station, the display shows "NO PTY".
GRUNDIG Service
105 340 1K 3K 10K
105 340 1K 3K
flag will light up.
105 340 1K 3K 10K
105 340 1K 3K
105 340 1K
105 340 1K
Ç
105 340 1K 3K
105 340 1K 3K
105 340 1K
105 340 1K 3K 10K
105 340 1K 3K 10K
105 340 1K 3K
105 340 1K
TUNER
Storing Preset Stations
You can store up to 20 stations in the FM
waveband, 10 stations in the MW and 10
T U N E R
stations in the LW waveband in the memory.
Hz
When a preset station is selected, the preset
number appears next to the frequency on the
display.
F M 8 7 0 0 M
10K Hz Hz
Manual programming
1 Press TUNER ( BAND ) on the set or remote
2 Press TUNER again to select the desired
TUNED
STEREO
F M 1 0 3 0 0 M
3 Press TUNING S or T to tune to the
Hz Hz
4 Press briefly PROGRAM
– The
5 Press PRESET A or B (or A or B on the
TUNED
PRESET STEREO
1 0 9 8 5 0 M
Hz – The preset number flashes on the display.
10K Hz
6 Press PROGRAM again.
TUNED
– The station and the preset number are stored
PRESET STEREO
S T O R E D
3K 10K Hz
• Repeat the above procedure to store other
Note: In case of a power interruption the preset
Tuning to Preset Stations
• Press PRESET A or B (or A or B on the
– The preset number and frequency appear on
TUNED
PRESET STEREO
1 0 9 8 5 0 M
Hz
3K 10K Hz
TUNER
RDS Search
RDS allows you to select memorized FM stations
according to programme type. More and more
stations are codifying their programme type
allowing efficient search with the SEARCH
function. The transmitted code is, however, the
responsibility of the radio station.
• By using the SEARCH button on the system or
R . D . S
N E W S
10K Hz
• Press S or T to start scanning the
R . D . S
A F F A I R S
10K Hz
R . D . S
I N F O
3K 10K Hz
RDS Clock
Some RDS station may be transmitting a real time
clock at an interval of every minute.
• If the clock time has not been set manually by
TUNED
R . D . S
PRESET STEREO
R A D I O 2
Hz
TUNED
R . D . S
PRESET STEREO
R O C K M
• If you have already set the clock time, the set
Hz
TUNED
R . D . S
PRESET STEREO
U S I C F O R
10K Hz
TUNED
R . D . S
PRESET STEREO
1 0 9 8 5 0 M
3K 10K Hz Hz
Allgemeiner Teil / General Section
control to select TUNER mode.
waveband: FM, MW or LW.
desired frequency.
flag flashes on the display.
PRESET
remote control) to select a preset number.
and STORED scrolls on the display.
preset stations.
stations will be kept in the memory for at
least one hour.
remote control) to select the desired preset
number.
the display.
on the remote control, you can call up the
programme types one after another.
memorized stations in forward or backward
direction to find a station broadcasting the
required programme type. As soon as such a
station is found it is tuned to.
you (e.g. '0:00' is flashing); the current RDS
clock time will be stored automatically when
the RDS station transmits the real time clock.
time will not be replaced when the RDS clock
time is being received
1 - 11