Inhaltsverzeichnis
Werbung
CASSETTE MODE
________________________________________________________________________
2
Insert the cassette into the compartment with the open side facing the back.
Note:
If you insert a cassette into the cassette compartment with side A facing
upwards, »
PAUSE« will begin the playback/recording on side A,
4
»
« will begin the recording on side B.
A
3
Close the cassette compartment by pressing
HiFi.
CLOSE
– The cassette compartment closes and the display reads: »CLOSE«.
Noise reduction system (Dolby NR)
For optimum playback quality, always play back the cassettes the way they were
recorded, meaning either with or without DOLBY B NR.
The advantage of recording with DOLBY NR is the improved noise voltage ratio.
Dolby Noise Reduction was manufactured under license from Dolby
Laboratories Licensing Corporation. DOLBY and the Double-D symbol
registered trademarks of the Dolby Laboratories Licensing Corporation.
NR stands for noise reduction.
DOLBY ON
1
Select this function by pressing »MODE« once. The display will show the
message »DOLBY ON« or »DOLBY OFF«.
2
Select the function »DOLBY ON« with »
1
– The message »
B NR« is shown in the display under the cassette
compartment as long as the Dolby system is activated.
Note:
DOLBY OFF
To deactivate the Dolby system, repeat the setting procedure and select
»DOLBY OFF«.
CASSETTE MODE
________________________________________________________________________
Track search
This function allows you to search for individual tracks on the cassette. Up to 15
tracks can be skipped in either direction.
1
Press »9« or »8« repeatedly during playback.
– The display shows »
« or »
«.
W
Q
– The system will wind the tape to the beginning of each track. Playback
begins at that point.
Note:
At least four seconds of pause must be recorded in between titles, so that the
track search function can detect individual tracks.
Very quiet passages in songs or live recordings may be identified as pauses
by the track search.
Switching the tape counter to real time
0 I50
1
To switch between the two, press »
i
«.
– The display shows the four-digit tape counter or real time in minutes and
seconds.
00 : 25
Note:
The real time measurement first needs to adjust to the thickness of the tape
material used.
Once playback is started, the colon between the minutes and seconds
display (- -:- -) will flash for a short while.
The thickness of the tape and other values are calculated during this time.
Once this process is completed, the real time is also shown during fast
forward and rewind.
Resetting the counter
0000
1
Press
»CANCEL
«.
– The display reads: »0000«. The counter is reset.
»TAPE
OPEN/CLOSE« on the
are
2
« or »
«.
41
43
CASSETTE MODE
________________________________________________________________________
Playback
Selecting the playback mode
1
Select this function by pressing »MODE« twice. The display will show the
message »CONT PLAY«, »AUTOREVERSE« or »REVERSE OFF«.
2
Select function with »
1
« or »
2
«.
cont. play
– »CONT. PLAY« – playback of both sides of the cassette is repeated
indefinitely. The display shows the symbol: »
autoreverse
– »AUTOREVERSE« – playback stops at the end of the second side of the
cassette. The display shows the symbol: »
reverse OFF
– »REVERSE OFF« – playback stops at the end of one side of the cassette.
The display shows the symbol: »
Playback
0000
1
Press »
PAUSE« to start playback.
4
Note:
The running direction of the cassette can be changed by pressing »
2
To pause playback, press »
4
PAUSE«.
To resume playback, press »
PAUSE« again.
4
3
To end playback, press »
«.
5
– When you start playback again the cassette will run in the direction last
chosen.
Fast forward/rewinding the cassette
1
From the STOP position, press »9« or »8«.
– The display shows »
« or »
W
Q
42
CASSETTE MODE
________________________________________________________________________
Storing a position on the cassette
1
To mark a position on the cassette, press »MEMORY« during playback at
the desired point of the tape.
– The display shows: »X«.
2
Press »
8
« after playback is stopped. The tape is wound to the marked spot
and stops there.
3
Exit the function by pressing »MEMORY«.
Recording
Erase protection
Every new recording overwrites the existing recording on the tape.
You can protect your own cassettes against accidental erasure by breaking the
safety tabs on the top of the cassette.
If you want to record on to a protected cassette, cover the opening with adhesive
tape.
1
Selecting the recording mode
1
Select this function by pressing »MODE« twice. The display will show the
message »CONT PLAY«, »AUTOREVERSE« or »REVERSE OFF«.
2
Select the function by pressing »
1
autoreverse
– »AUTOREVERSE« – recording stops at the end of the second side of the
cassette. The display shows: »
H
reverse OFF
– »REVERSE OFF« – recording stops at the end of the current side of the
cassette. The display shows: »
G
Note:
If you have selected the »CONT PLAY« function, this will be automatically
switched to »AUTOREVERSE«.
44
J
«.
H
«.
G
«.
«.
«.
2
« or »
«.
«.
«.
Werbung
Inhaltsverzeichnis
