Specifications - Makita 4101RH Betriebsanleitung

ENGLISH
(Original instructions)
1 TEST button
2 RESET or "ON" button
3 Pilot lamp
4 Portable residual current device
(PRCD)
5 Wing bolt
6 Base
7 Wing nut
8 End of blade case
9 Red line

SPECIFICATIONS

Model
Wheel diameter ................................................ 125 mm
Max. cutting capacities
90° ................................................................ 41.5 mm
45° ................................................................... 26 mm
–1
No load speed (min ) ........................................ 12,000
Overall length ................................................... 236 mm
Net weight............................................................ 3.0 kg
Safety class ........................................................ Class I
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting in brick, concrete and
stone with the use of water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. This tool
should be grounded while in use to protect the operator
from electric shock. Use only three-wire extension cords
which have three-prong grounding-type plugs and three-
pole receptacles which accept the tool's plug.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CUTTER SAFETY WARNINGS
1. Read all safety warnings, instructions, illustra-
tions and specifications provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or seri-
ous injury.
Explanation of general view
10 Top guide
11 Switch trigger
12 Lock-off button
13 Wrench 22
14 Hex wrench
15 Inner flange
16 Diamond wheel
17 Outer flange
18 Hex socket head bolt
19 Blade case
2.
4101RH
3.
4.
5.
ENE023-1
6.
ENF001-1
7.
8.
GEA010-1
9.
GEB025-2
20 Water pipe
21 Clamp
22 Cover (A)
23 Cover (B)
24 Screw
25 Limit mark
26 Brush holder cap
27 Screwdriver
Always use guard provided with the tool. The
guard must be securely attached to the power
tool and positioned for maximum safety, so the
least amount of wheel is exposed towards the
operator. The guard helps to protect operator from
broken wheel fragments and accidental contact with
wheel.
Use only diamond cut-off wheel for your power
tool. Just because the accessory can be attached to
your power tool, it does not assure safe operation.
The rated speed of the wheel must be at least
equal to the maximum speed marked on the
power tool. Wheels running faster than their rated
speed can break and fly apart.
Always use undamaged wheel flanges that are of
correct diameter for your selected wheel. Proper
wheel flanges support the wheel thus reducing the
possibility of wheel breakage.
The outside diameter and the thickness of your
wheel must be within the capacity rating of your
power tool. Incorrectly sized wheels cannot be ade-
quately guarded or controlled.
The arbour size of wheels and flanges must
properly fit the spindle of the power tool. Wheels
and flanges with arbour holes that do not match the
mounting hardware of the power tool will run out of
balance, vibrate excessively and may cause loss of
control.
Do not use damaged wheels. Before each use,
inspect the wheels for chips and cracks. If power
tool or wheel is dropped, inspect for damage or
install an undamaged wheel. After inspecting
and installing the wheel, position yourself and
bystanders away from the plane of the rotating
wheel and run the power tool at maximum no
load speed for one minute. Damaged wheels will
normally break apart during this test time.
Wear personal protective equipment. Depending
on application, use face shield, safety goggles
or safety glasses. As appropriate, wear dust
mask, hearing protectors, gloves and shop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must be
capable of stopping flying debris generated by vari-
ous operations. The dust mask or respirator must be
capable of filtrating particles generated by your oper-
ation. Prolonged exposure to high intensity noise
may cause hearing loss.
7