Initial Operation - Bosch Active Line Drive Unit Originalbetriebsanleitung

English–3
Assembly
Inserting and removing the battery pack
For inserting and removing the eBike battery pack in/from the
eBike, please read and observe the battery pack operating in-
structions.
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer 3, slide it from the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 15
and slide the on-board computer toward the front out of the
holder 4.
 Remove the on-board computer when you park the
eBike.
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4 from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 16 (thread M3, 8 mm long) from below into the
thread provided in the holder. Mount the holder back onto the
handlebar.
Checking the Speed Sensor (see figure B)
The speed sensor 17 and its spoke magnet 18 must be
mounted in such a manner that the spoke magnet, after a turn
of the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the distance between speed sensor 17 and spoke
magnet 18 is too small or too large, or if the speed sensor 17
is not properly connected, the speed indication f will fail, and
the eBike drive unit will operate in emergency mode.
In this case, loosen the screw of the spoke magnet 18 and fas-
ten the spoke magnet to the spoke in such a manner that it runs
past the mark of the speed sensor at the correct clearance. If
the speed is still not being indicated in the speed indication f
after this, please contact an authorised bicycle dealer.
Operation

Initial Operation

Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery pack is inserted (see battery
pack operating instructions).
– The on-board computer is properly inserted in the holder
(see "Inserting and removing the on-board computer",
page English–3).
– The speed sensor is connected properly (see "Checking
the Speed Sensor", page English–3).
Bosch eBike Systems
Switching the eBike System On/Off
Options for switching on the eBike system:
– If the on-board computer is already switched on when you
insert it into the holder, then the eBike system will be
switched on automatically.
– When the on-board computer and the eBike battery pack
are inserted, briefly press the On/Off button 5 of the on-
board computer.
– When the on-board computer is inserted, press the On/Off
button of the eBike battery pack (see battery pack operat-
ing instructions).
The drive is activated as soon as you step on the pedals (ex-
cept when in the push aid feature, see "Switching the Push-
assistance mode On/Off", page English–5). The motor out-
put depends on the settings of the assistance level on the on-
board computer. As soon as the system is activated, "Active
Line" will appear briefly on the display.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25 km/h, the assistance
from the eBike drive is switched off. The drive is automatically
re-activated as soon you start pedaling again and the speed is
below 25 km/h.
Options for switching off the eBike system:
– Press the On/Off button 5 of the on-board computer.
– Switch the eBike battery pack off by its On/Off button (see
battery pack operating instructions).
– Remove the on-board computer out of its holder.
If the eBike is not moved and no button is pressed on the on-
board computer for 10 minutes, the eBike system will shut
down automatically in order to save energy.
eShift (optional)
eShift is the integration of automatic gear shifting systems in-
to the eBike system. To support the rider in the best way pos-
sible, the function indications and the basic settings menu
have been adapted for the "eShift" function.
eShift with NuVinci H|Sync
The optimum gear for the respective speed is automatically
set according to a pre-defined desired cadence. In manual
mode you can choose between multiple gears.
In the " NuVinci Cadence" mode you can use the "–" or
"+" button on the operating unit to increase or decrease the
desired cadence. If you hold down the "–" or "+" button, the
cadence will increase or decrease in steps of five. The desired
cadence is shown on the display.
In the " NuVinci Gear" mode you can use the "–" or "+"
button on the operating unit to switch back and forth between
several defined transmission ratios. The engaged transmis-
sion ratio (gear) is shown on the display.
0 276 001 SAI | (29.5.15)