Declaration Of Conformity; Initial Operation - Bosch Performance Line Nyon BUI275: 1 270 020 915 Originalbetriebsanleitung

OBJ_BUCH-2616-003.book Page 2 Wednesday, June 14, 2017 2:24 PM
English–2
7 Brightness sensor
8 USB port
9 Protective cap of USB port
10 Operating unit
11 Joystick on the operating unit
12 "Home" button on the operating unit
13 Decrease assistance level button
14 Increase assistance level button
15 Button push/start aid "WALK"
16 Lock latch for on-board computer
17 Locking screw for on-board computer
USB charging cable (Micro A – Micro B)*
* not illustrated; available as accessory
Technical Data
On-board computer
Article number
Internal memory in total
Max. charging current,
USB connection mA
Charging voltage,
USB connection
1)
USB charging cable
Operating temperature
Storage temperature
Charging temperature
Internal lithium-ion battery
mAh
2)
Protection type
Supported wi-fi standards
WLAN
– Frequency MHz
– Transmission power mW
®
– Frequency MHz
– Transmission power mW
Weight, approx.
1) Not included as part of standard delivery
2) When USB cover is closed

Declaration of Conformity

Hereby, Robert Bosch GmbH, Bosch eBike Systems declares
that the radio equipment type Nyon 1 270 020 915 is in com-
pliance with Directive 2014/53/EU. The full text of the EU
declaration of conformity is available at the following internet
address:
https://www.ebike-connect.com/conformity
1 270 020 XBN | (14.6.17)
Assembly
Inserting and removing the on-board computer
(see figure A)
To insert the on-board computer 3, slide it from the front into
the holder 4.
To remove the on-board computer 3, press the lock latch 16
and slide the on-board computer toward the front out of the
holder 4.
 Remove the on-board computer when you park the
It is possible to secure the on-board computer against remov-
al in the holder. To do so, remove the holder 4 from the han-
dlebar. Put the on-board computer in the holder. Screw the
locking screw 17 (thread M3, 8 mm long) from below into the
thread provided in the holder. Mount the holder back onto the
handlebar.
Nyon
1 270 020 915
Operation
GB 8

Initial Operation

500
Requirements
The eBike system can only be activated when the following re-
V 5
quirements are met:
1 270 016 360
– A sufficiently charged eBike battery pack is inserted (see
°C –5...+40
°C –10...+50
– The on-board computer is properly inserted in the holder
°C 0...+40
V 3.7
710
Switching the eBike System On/Off
IP x7 (watertight) Options for switching on the eBike system:
– Place the on-board computer into the holder 4.
802.11b/g/n
– When the on-board computer and the eBike battery pack
(2.4 GHz)
2400–2480
– With the on-board computer inserted, push the On/Off
< 100
2400–2480
< 10
kg 0.2
The drive is activated as soon as you step on the pedals (ex-
cept for in the push assistance function or in assistance level
"OFF"). The motor output depends on the settings of the as-
sistance level on the on-board computer.
As soon as you stop pedaling when in normal operation, or as
soon as you have reached a speed of 25/45 km/h, the assis-
tance from the eBike drive is switched off. The drive is auto-
matically re-activated as soon you start pedaling again and the
speed is below 25/45 km/h.
eBike.
operating instructions of the battery pack).
(see "Inserting and removing the on-board computer",
page English–2).
are inserted, briefly press the On/Off button 5 of the on-
board computer.
button on the eBike battery (bicycle manufacturer solu-
tions are possible whereby there is no access to the bat-
tery On/Off button; see the battery operating instruc-
tions).
Bosch eBike Systems