Herunterladen Inhalt Inhalt Diese Seite drucken

Bosch Active Line Drive Unit Originalbetriebsanleitung Seite 18

Fuer diamant und trek e-bikes ride+ klasse
Vorschau ausblenden Andere Handbücher für Active Line Drive Unit:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

English–5
The following assistance levels (max.) are available:
– "OFF": The motor assistance is switched off, and the eBike
can be moved as a normal bicycle only by pedalling. The
push assistance cannot be activated in this assistance lev-
el.
– "ECO": Effective assistance at maximum efficiency for
maximum cruising range
– "TOUR": Uniform assistance, for touring with long cruising
range
– "SPORT": Powerful assistance for sportive riding off road
as well as for urban traffic
– "TURBO": Maximum assistance, supporting highest ca-
dence for sportive riding
To increase the assistance level, press the "+" 13 button on
the operating unit until the desired assistance level appears in
the display b. To decrease the assistance level, press the
button"–" 12.
The requested motor output is displayed in indicator a. The
maximum motor output depends on the selected assistance
level.
Assistance Level
"ECO"
"TOUR"
"SPORT"
"TURBO"
* The motor output can vary for individual versions.
When the on-board computer is removed from the holder 4,
the last indicated assistance level is stored; the motor-output
indicator a remains empty.
Switching the Push-assistance mode On/Off
The push-assistance feature makes it easier to push the
eBike. The speed in this function depends on the set gear and
cannot exceed 6 km/h (max.). The lower the set gear, the low-
er the speed in the push-assistance function (at full output).
 The push-assistance function may only be used when
pushing the eBike. Danger of injury when the wheels of
the eBike do not have ground contact while using the push-
assistance function.
To activate the push-assistance function, press and hold the
"WALK" button 14 on the operating unit. The eBike's drive is
activated.
Note: The push assistance cannot be activated in the "OFF"
assistance level.
The push assistance is switched off if one of the following
occurs:
– you release the "WALK" 14 button,
– the wheels of the eBike are blocked (e.g. by actuating the
brakes or impacting against an obstacle),
– the speed exceeds 6 km/h.
Bosch eBike Systems
Assistance Factor*
40%
100%
150%
250%
Back-pedalling function (optional)
For bikes with back-pedalling function, the pedals rotate
when the push aid is switched on. If the rotating pedals are
blocked, the push aid switches off.
Switching bike lights on/off
In the model in which the lighting is powered by the eBike sys-
tem, the front and rear lights can be switched on and off at the
same time via the on-board computer with button 2.
When the lighting is switched on "Lights on" appears and
when the lighting is switched off "Lights off" appears for ap-
prox. 1 s in text indication d. The lighting symbol c is dis-
played when the light is on.
Switching the bike light on and off has no effect on the back
lighting of the display.
Displays and configurations of the on-board
computer
Speed and Distance Indication
The speed indication f always displays the current speed.
The following functions are available in the function indica-
tion (combination of text indication d and value indication e):
– "Clock": Current time
– "Max. speed": Maximum speed achieved since the last
reset
– "Avg. speed": Average speed achieved since the last reset
– "Trip time": Trip time since the last reset
– "Range": Estimated range of the available battery-pack
charge (for constant conditions such as assistance level,
route profile, etc.)
– "Odometer": Display of the total distance travelled with
the eBike (cannot be reset)
– " NuVinci Cadence/Gear": This menu item is displayed
only in conjunction with a Nu Vinci H|Sync automatic trans-
mission.
If you press the "i" button for longer than 1 s, you will
access the NuVinci menu item from any menu item in the
information menu.
To switch from the " NuVinci Cadence" mode to the
" NuVinci Gear" mode, press the "i" button for 1 s.
To switch from the " NuVinci Gear" mode to the
" NuVinci Cadence" mode, all you have to do is briefly
press the "i" button.
The default setting is " NuVinci Cadence".
Range
Odometer
NuVinci Cadence
(1 s)
(1 s)
NuVinci Gear
0 276 001 SAI | (29.5.15)

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis