Special Accessories; Ec Declaration Of Conformity; Troubleshooting - Scheppach Basa 3.0v Originalbetriebsanleitung

Special Accessories

Cross cutting jig
Circular cutting device
Bit stop
Grinding belt device
Underframe for tables
Automatic starter, type ALV 2
Type ALV 10
Saw bands
for wood:
12/0.5/2360 mm, 4 teeth/inch
Standard saw band
15/0.5/2360 mm, 4 teeth/inch
Straight upright cuts with longitudinal stop
for wood and synthetic materials:
6/0.5/2360 mm, 6 teeth/inch
Turning works with small radius 25 mm
12/0.5/2360 mm, 6 teeth/inch
Precision cutting works
Different materials:
wood, synthetic materials, metals
3.5/0.5/2360 mm, 14 teeth/inch
Extra-fine cutting works, extremely small radiuses
Non-ferrous metals up to 10 mm
6/0.65/2360 mm, 22 teeth/inch
straight cuts and turning works
Synthetic materials, non-ferrous metals
6/0.65/2360 mm, 10 teeth/inch
Synthetic materials, non-ferrous metals above 15 mm
straight cuts and large radiuses > 60 mm
Failure
Saw blade gets loose after
turning off the motor
Motor does not start
Motor runs forward or
backwards
No motor output
turns off automatically
Burns on the cutting
c) with longitudinal cuts
d) with cross cuts
7312 0025
}
7319 0710
7319 0709
7910 4010
7910 4020
7319 0701
7319 0704
7319 0702
7319 0705
7319 0706
73190707
73190703

Troubleshooting

Possible cause
a) Fastening nut tightened
insufficiently
a) Fastening nut tightened insufficiently a) Check the mains fuse.
b) Extension cable defect
manual
c) Connections on the motor or
switch defect
d) Motor or switch defect
manual
Capacitor defect
Overload by dull saw
turned on again
blade, thermoprotection is triggered
a) Fastening nut tightened insufficiently a) Insert a sharpened saw blade
longitudinal cuts
c) Longitudinal stop not parallel
d) Slide carriage not parallel

EC Declaration of Conformity

We, scheppach Fabrikation von Holzbearbeitungsmaschinen GmbH, Günz-
burger Str. 69, D-89335 Ichenhausen
hereby declare that the machine named below correspondends to the
relevant safety and health requirements of the EC guide lines speci-
fied below in its design and construction and in the version which we
introduced to the market.
This declaration becomes invalid if changes are made to the machine
without our consent.
Machine description:
Band saw
Machine model:
Basa 3.0v (Art.No. 1901503901 /
1901503902)
Relevant EC directives: EC machine directive 2006/42/EG
EC Low voltage directive 2006/95/EWG,
EC-EMV directive 2004/108/EWG.
Applied harmonized European Standards:
EN 12100-1, EN 12100-2, EN 294, EN 349,
EN 418, EN 847-1, EN 13849-1, EN 1088,
EN 1807-1, EN 50082-1, EN 60204-1,
EN 55014, EN 60555-2, EN 60555-3
Notified body within the meaning of Annex VII
Prüf- und Zertifizierungsstelle
Fachausschuss Holz
Vollmoellerstraße 11
70563 Stuttgart-Vaihingen
Date
Ichenhausen, 18.03.2011
Signature:
on behalf of Werner Hartmann
(Technical manager)
Solution
a) Tighten fastening nut, M20 left-handed thread
b) See "Electrical Connection" in the operating
c) Have it checked by an electrician
Brake does not bleed
d) See "Electrical Connection" in the operating
Have it exchanged by an electrician
Insert a sharpened saw blade; motor can be
after the cooling period
c) Exchange the longitudinal stop
Align the slide carriage with the saw blade
15