Siemens SINUMERIK 840D sl Bedienhandbuch Seite 15

10.1.16 Positionen wiederholen........................................................................................................354
10.2 Drehen.................................................................................................................................355
10.2.1 Allgemeines..........................................................................................................................355
10.2.2 Abspanen (CYCLE951)........................................................................................................355
10.2.3 Einstich (CYCLE930)...........................................................................................................358
10.2.4 Freistich Form E und F (CYCLE940)...................................................................................361
10.2.5 Gewindefreistiche (CYCLE940)...........................................................................................363
10.2.6 Gewindedrehen (CYCLE99)................................................................................................366
10.2.7 Gewindekette (CYCLE98)....................................................................................................382
10.2.8 Abstich (CYCLE92)..............................................................................................................388
10.3 Konturdrehen.......................................................................................................................389
10.3.1 Allgemeines..........................................................................................................................389
10.3.2 Darstellung der Kontur.........................................................................................................391
10.3.3 Neue Kontur anlegen...........................................................................................................392
10.3.4 Konturelemente erstellen.....................................................................................................394
10.3.5 Passungsmaß eingeben......................................................................................................399
10.3.6 Kontur ändern......................................................................................................................400
10.3.7 Konturaufruf (CYCLE62) - nur bei G-Code-Programm........................................................401
10.3.8 Abspanen (CYCLE952)........................................................................................................402
10.3.9 Abspanen Rest (CYCLE952)...............................................................................................410
10.3.10 Stechen (CYCLE952)...........................................................................................................412
10.3.11 Stechen Rest (CYCLE952)..................................................................................................418
10.3.12 Stechdrehen (CYCLE952)...................................................................................................419
10.3.13 Stechdrehen Rest (CYCLE952)...........................................................................................425
10.4 Fräsen..................................................................................................................................427
10.4.1 Planfräsen (CYCLE61).........................................................................................................427
10.4.2 Rechtecktasche (POCKET3)...............................................................................................431
10.4.3 Kreistasche (POCKET4)......................................................................................................440
10.4.4 Rechteckzapfen (CYCLE76)................................................................................................450
10.4.5 Kreiszapfen (CYCLE77).......................................................................................................457
10.4.6 Mehrkant (CYCLE79)...........................................................................................................463
10.4.7 Längsnut (SLOT1)................................................................................................................468
10.4.8 Kreisnut (SLOT2).................................................................................................................477
10.4.9 Offene Nut (CYCLE899)......................................................................................................484
10.4.10 Langloch (LONGHOLE) - nur bei G-Code-Programm.........................................................495
10.4.11 Gewindefräsen (CYCLE70)..................................................................................................497
10.4.12 Gravur (CYCLE60)...............................................................................................................501
10.5 Konturfräsen.........................................................................................................................507
10.5.1 Allgemeines..........................................................................................................................507
10.5.2 Darstellung der Kontur.........................................................................................................507
10.5.3 Neue Kontur anlegen...........................................................................................................509
10.5.4 Konturelemente erstellen.....................................................................................................511
10.5.5 Kontur ändern......................................................................................................................516
10.5.6 Konturaufruf (CYCLE62) - nur bei G-Code-Programm........................................................517
10.5.7 Bahnfräsen (CYCLE72).......................................................................................................519
10.5.8 Konturtasche/Konturzapfen (CYCLE63/64).........................................................................524
10.5.9 Konturtasche vorbohren (CYCLE64)...................................................................................526
10.5.10 Konturtasche fräsen (CYCLE63)..........................................................................................530
10.5.11 Konturtasche Restmaterial (CYCLE63, Option)...................................................................536
10.5.12 Konturzapfen fräsen (CYCLE63).........................................................................................538
Drehen
Bedienhandbuch, 10/2015, 6FC5398-8CP40-5AA3
Inhaltsverzeichnis
15