Error Messages On The Display - Schulthess Spirit proLine WEI 9080 Bedienungsanleitung

Problems
Repairs, alterations or intervention on electronic equip-
ment should only be carried out by qualified specialists.
Inexpert repairs can cause considerable damage and risk
to the user.
Only original spare parts should be used for repairs.
Please find below minor faults which you can rectify
yourself.

Error messages on the display

If the following error messages are displayed, the pro-
gramme can be restarted by pressing the start button
once the error has been rectified.
«CHILD LOCK ACTIVE»
X Hold the Quick Wash button down and press the
Start button.
«PLEASE CLOSE DOOR»
X Push the door closed until the lock catches properly.
«PLEASE START AgAIn»
If the door was closed subsequently, the Start button
must be pressed again.
After a power failure you must press the Start button.
«CHECK WATER SUPPLy»
X Turn on the tap and start again.
X Filter in water supply is blocked: Clean the filter, see
chapter «Cleaning and Maintenance / Cleaning the filters
in the water inlet».
X Interruption in water supply.
«CHECK DRAIn»
X Check whether the drainage hose is blocked.
X Foreign bodies block the drain pump: clean pump
according to chapter «Cleaning and Maintenance /Emer-
gency emptying».
X The water drain provided by the customer is blocked:
Carry out an emergency discharge according to chapter
«Cleaning and Maintenance» and clean the drain siphon
(built-in siphon).
X The position of the drain hose is too high. The maximum
pumping height is 1m above ground.
«UnBALAnCE nO SPInnIng»
X Excessive imbalance. Laundry not spun.
X Press the start button and then the Quick Wash button
to end the wash programme.
X Open the door and redistribute the load.
X Repeat the spin cycle with the separate spin programme.
General information:
X Avoid loading the drum with one single heavy item.
Wash large and small laundry together.
«FOAM PROg. ExTEnD»
X The washing machine has detected foam and taken
adequate measures. The spinning cycle of the laundry
could be completed.
In future, please reduce the detergent quantity.
56
«FOAM, PROg. CAnCEL»
X Due to extremely intensive foaming, the washing
machine could not complete the spinning cycle and the
wash programme had to be aborted.
X Repeat the wash programme without adding any
detergent.
X In future, please reduce the detergent quantity (if
re quired use washing powder instead of liquid deter-
gent).
«WATER LEVEL TOO HIgH»
Too much foam in the washing machine, spinning has
not been effected. There are two possibilities to solve
the problem:
a) Press the Start button and then interrupt the pro-
gramme by pressing the Quick Wash button several times
until the display «OPEN DOOR» appears.
Mix approx. 30 ml conditioner and approx. 1 litre water.
Start the previously selected wash programme (it may
take several minutes until the machine is released for the
selection of a new programme). After the water s upply
has been com pleted, switch forward immediately to
«Conditio ning» by pressing the Quick Wash button and
add the conditioner- water mixture into compartment A
of the detergent drawer. The programme should now
end as usually and the spinning process should take place.
Afterwards repeat the desired programme, however
without any detergent.
or
b) Press the Start button and then interrupt the pro-
gram me by pressing the «Quick wash» button several
times until the display «OPEN DOOR» appears. Wait for
approx. 1 hour and start the previously selected wash
programme, move forward immediately to «spinning»
using the Quick Wash button. Usually the laundry will
be spun. If not, repeat the procedure including waiting
for 1 hour. After wards repeat the desired programme,
however without any detergent.
X The maximum admissible water level is reached. Wait
until the water has been pumped out completely and
press the Start button. The programme will continue.
«WATER IS BEIng PUMPED OUT»
Too much water is in the washing machine. Water is
pumped off to the set level.
If you see a lot of foam in the door glass, this means
that too much foam is in the washing machine.
To eliminate this problem proceed as for the error mes-
sage «Water level too high».
In future, please reduce the detergent quantity.
«MAInS SUPPLy BLOCKED»
In the case of electrically-heated machines, the appli-
ance may be shut down by external energy manage-
ment systems at times of peak power loads.
The mains supply inhibition will only cause a stop of
programme during the heating phase.
In this condition all operating buttons are blocked ex-
cept for the Quick wash button, and the time remaining
display is stopped. The control light for the start button
lights up.
The programme steps Rinsing, Conditioning and
Spin ning will be executed in spite of the inhibited mains
supply.
When the mains blocking is ended, the washing pro-
gram me is resumed automatically and the display reacti-
vated. The heating is switched back on after a 15-se-
cond delay.