Assembly And Operation; Before Commissioning - Scheppach 4901305901 Originalbetriebsanleitung

7.

Assembly and operation

Before commissioning

• Prior to commissioning, all covers and safety devic-
es must be mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that the
saw blade is correctly fitted, and that moving parts
run smoothly.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
• Only connect the machine to a correctly installed protec-
tive contact socket, with fuse protection of at least 16A.
• Use a residual current circuit breaker with a trigger
current of 30 mA or less.
Attention! Remove the mains plug before any mainte-
nance, modification and assembly work on the circular
saw.
Place all supplied parts on a flat surface. Group iden-
tical parts.
Note: If connections are secured with a screw (round
head/or hexagon), hexagonal nuts and washer, the
washer must be placed under the nut.
Insert screws from the outside to the inside and secure
connections with nuts from the inside.
Note: During assembly, tighten the nuts and bolts only
to the extent that they cannot fall off.
If you tighten the nuts and screws fully before final as-
sembly, the final assembly cannot be carried out.
m Attention!
Always make sure the product is fully assembled
before commissioning!
Fig. 1
Place the tabletop (1) on a workbench (remove packing
pad a under the motor).
Fig. 1.1
Mount the frame leg (2) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts.
Fig. 2
Mount the switch (6) to the tabletop with 2 M6 x 16 hex-
agonal bolts, 2 washers 6 and 2 M6 nuts.
32 | GB
Fig. 3
Mount the frame leg (3) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts.
Fig. 4
Mount the frame leg (4) to the tabletop with 2 M6 x 16
hexagonal bolts, 2 washers 6 and 2 M6 nuts.
Fig. 5
Mount the frame leg (5) and the hose holder (b) to the
tabletop with 2 M6 x 16 hexagonal bolts, 2 washers 6
and 2 M6 nuts.
Fig. 6 / 6.1
Mount 2 longitudinal struts (10) and 2 cross members
(9), to the frame legs (2, 3, 4 and 5) with 12 M6 x 16 hex-
agonal bolts, 12 washers 6 and 12 M6 hexagonal nuts.
Fig. 7 / 7.1 / 7.2 / 7.3
Mount the table extension plate (8), with two struts (11), to
the tabletop and cross member with 6 M6 x 16 hexagonal
bolts, 6 washers 6, and 6 M6 hexagonal nuts. Tighten the
bolts lightly by hand. (The tabletop (8) can also be mounted
laterally as a table width extension with the shorter struts)
Fig. 8
Fit the suction port (14) to the lower saw blade guard
(13) with 4 M4 x 10 hexagonal bolts and 4 x washers 4.
Fig. 9
Mount the travel fixture (16) to the rear frame legs (4
and 5) with 4 M6 x 16 hexagonal bolts, 4 washers 6,
and 4 M6 nuts.
Fig. 10
Place the machine on its feet, tighten all screws of the
table, feet and struts (except the travel fixture).
Fig. 11
Tighten the travel fixture in position such that the
wheels lightly touch the floor.
Fig. 12 / 12.1
Mount the riving knife to the saw blade as described
in the illustration. Loosen the screw slightly (do not un-
screw it completely) and tighten it again after the ad-
justment. In doing so, the saw blade insert (19, Fig. 13)
must be removed.
www.scheppach.com