Before Starting The Equipment; Attachment And Operation - Scheppach Mst254 Originalbetriebsanleitung

Noise
Total noise values determined in accordance with
EN 62841.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing.
The above-mentioned noise emission values were meas-
ured in accordance with a standardised test procedure
and can be used to compare one power tool with another.
The above-mentioned noise emission values can also
be used for the preliminary assessment of exposure.
Warning:
• The noise emissions during the actual use of the
power tool may differ from the above-mentioned
values depending on the power tool being used, in
particular on the type of workpiece being processed.
• Try to keep emissions as low as possible. For exam-
ple: Limit your working time. In this regard, all the
operational cycle phases must be taken into consid-
eration (such as the times when the tool is switched
off or running idle).
7.

Before starting the equipment

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans-
port damage.
• If possible, store the packaging until the warranty
period has expired.
DANGER
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The equipment must be set up where it can stand
securely. Secure the machine on a workbench or a
base frame with 4 screws (not included in delivery)
using the holes on the fixed saw table (15).
• Pull out the pre-installed tilt protection (36) com-
pletely and secure it with an Allen key (D) (fig.2).
• All covers and safety devices have to be properly
fitted before the equipment is switched on.
• It must be possible for the blade to run freely.
101.6 dB(A)
• When working with wood that has been processed
3 dB
before, watch out for foreign bodies such as nails
114.6 dB(A)
or screws, etc.
• Before you press the ON/OFF switch check that the
3 dB
saw blade is fitted correctly. Moving parts must run
smoothly.
• Before you connect the equipment to the power sup-
ply make sure the data on the rating plate are identi-
cal to the mains data.
7.1 Checking the moving saw blade guard safety
device (5)
The saw blade guard protects against accidental con-
tact with the saw blade and from chips flying around.
Check the function
To do so, fold the saw downwards:
• The saw blade guard must provide free access to
the saw blade without touching other parts.
• When folding the saw upwards into the starting posi-
tion, the saw blade guard must cover the saw blade
automatically.

8. Attachment and operation

m Attention!
Always make sure the device is fully assembled
before commissioning!
8.1 Attaching the sliding compound mitre saw (fig.
1/2/4/5/23)
• In order to adjust the rotary table (14), fold the lock-
ing handle (11) upwards and pull up the latched posi-
tion lever (35) with your index finger.
• Turn the rotary table (14) and pointer (12) to the de-
sired angle measurement of the scale (13). To fix the
setting, fold the locking handle (11) downwards.
• Pressing the machine head (4) lightly downwards
and removing the locking bolt (23) from the motor
bracket at the same time disengages the saw from
the lowest position.
• Swing the machine head (4) up.
• It is possible to secure the clamping devices (7) to the
left or right on the fixed saw table (15). Insert the clamp-
ing devices (7) in the holes on the rear side of the stop
rail (16) and secure it with the star grip screws (7a).
www.scheppach.com GB | 37