Technical Data - Scheppach 4901305901 Originalbetriebsanleitung

Safety instructions for the use of saw blades
1 Only use insertion tools if you have mastered
their use.
2 Observe the maximum speed. The maximum
speed specified on the insertion tool may not be
exceeded. If specified, observe the speed range.
3 Observe the motor / saw blade direction of rotation.
4 Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5 Clean dirt, grease, oil and water off of the clamping
surfaces.
6 Do not use any loose reducing rings or bushes to
reduce holes on circular saw blades.
7 Make sure that fixed reducer rings for securing the
insertion tool have the same diameter and have at
least 1/3 of the cutting diameter.
8 Make sure that fixed reducer rings are parallel to
each other.
9 Handle insertion tool with caution. They are ideally
stored in the originally package or special contain-
ers. Wear protective gloves in order to improve
grip and to further reduce the risk of injury.
10 Prior to the use of insertion tools, make sure that
all protective devices are properly fastened.
11 Prior to use, make sure that the insertion tool
meets the technical requirements of this electric
tool and is properly fastened.
12 Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Residual risks
The power tool is state-of-the-art and has been built
according to the recognised technical safety regula-
tions. However, individual residual risks can arise dur-
ing operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been met,
some non-obvious residual risks may still remain.
• Residual risks can be minimised if the "safety in-
structions" and the "Proper use" are observed along
with the whole of the operating instructions.
• Do not unnecessary stress the machine: too much
pressure when sawing will damage the saw blade
quickly. This results in reduced output of the ma-
chine in the processing and in cut precision.
• Avoid accidental starting of the machine: the oper-
ating button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual. In
doing so, your saw provides optimal performance.
• Keep your hands away from the working area when
the machine is in operation.
• Before performing setting or maintenance work,
switch the device off and unplug the mains plug.

6. Technical data

AC motor
Power
Operating mode
Idle speed
Plug
Weight approx.
Carbide saw blade 24 Z
pre-mounted
Carbide saw blade 48 Z
Table size
Cutting height max. 90°
Cutting height max. 45°
Height adjustment
Tilting saw blade
* Operating mode S6 40%: Continuous duty with inter-
mittent loading (operating time 10 mins). In order avoid
impermissible overheating of the motor, the motor should
be driven for only 40% of the operating time with the
stipulated nominal power and must then continue to run
with no load for the remaining 60% of the operating time.
Noise level
The noise levels have been determined in accordance
with EN 1870.
Sound pressure level L
Uncertainty K
Sound power level L
Uncertainty K
Wear hearing protection.
Excessive noise can result in a loss of hearing. Total
vibration emission values (vector sum of three direc-
tions) determined per EN 1870.
www.scheppach.com
230 V~ 50Hz
2200 W
S6 40%*
2800 rpm
Schuko
55 kg
Ø 315 x Ø 30 x 3 mm
Ø 315 x Ø 30 x 3.2 mm
800 x 550 (950) mm
83 millimeters
53 millimeters
pA
pA
WA
WA
400 V~ 50 Hz
2800 W
S 6/40 %
2800 rpm
CEE 16 A
57 kg
0 - 83 mm
0 - 45°
90.2 dB
3 dB
105.2 dB
3 dB
GB | 31