Scheppach MST305 Originalbetriebsanleitung Seite 34

Noise and vibration
The noise and vibration levels have been determined
in accordance with EN 62841.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
Exposure to noise can cause hearing loss. Total vibra-
tion emission values (vector sum of three directions)
determined per EN 62841.
The specified noise emission values have been meas-
ured in accordance with a standardised test procedure
and can be used to compare one power tool with an-
other. The specified device emissions values can also
be used for an initial estimation of the load.
m WARNING
• The noise emission values can vary from the spec-
ified values during the actual use of the power tool,
depending on the type and the manner in which the
electric tool is used, and in particular the type of
workpiece being processed.
• Try to keep the stress as low as possible. For example:
Limit working time. In the process all parts of the oper-
ating cycle must be taken into account (such as times
in which the power tool is switched off or time in which
it is switched on, but is not running under a load).
8. Unpacking
• Open the packaging and carefully remove the product.
• Remove the packaging material, as well as the pack-
aging and transport safety devices (if present).
• Check whether the scope of delivery is complete.
• Check the product and accessory parts for transport
damage. In the event of complaints the carrier must
be informed immediately. Later claims will not be
recognised.
• If possible, keep the packaging until the expiry of the
warranty period.
• Familiarise yourself with the product by means of the
operating manual before using for the first time.
• With accessories as well as wearing parts and re-
placement parts use only original parts. Spare parts
can be obtained from your specialist dealer.
34 | GB
• When ordering please provide our article number as
well as type and year of manufacture for the product.
m WARNING!
The product and the packaging material are not
95 dB
children's toys! Do not let children play with plas-
3 dB
tic bags, films or small parts! There is a danger of
choking or suffocating!
108 dB
3 dB
9. Assembly and operation
m ATTENTION!
Always make sure the product is fully assembled
before commissioning!
• The machine must be securely installed, i.e. bolted
down on a workbench, machine stand or similar.
Use the holes in the machine frame for this.
• Prior to commissioning, all covers and safety devic-
es must be mounted correctly.
• The saw blade must be able to run freely.
• In case of previously machined wood, be aware of
any foreign bodies, such as nails or screws, etc.
• Before pressing the on/off switch, make sure that
the saw blade is correctly fitted, and that moving
parts run smoothly.
• Before connecting the machine, make certain that
the data on the type plate matches with the mains
power data.
9.1 Setting up the saw (Fig. 1 - 8)
• To adjust the rotary table (14), push the locking knob
(10) downwards and pull the lower indexed position
lever (11) upwards with your index finger.
• Rotate the rotary table (14) and pointer (12) to the
desired angle on the scale (13) and lock in place by
folding up the locking knob (10).
• The saw is unlocked from the lower position by gen-
tly pressing down on the machine head (19) and, at
the same time, pulling out the locking pin (21) from
the engine mount.
• Swivel the machine head (19) upwards.
• The clamping device (15) can be attached to both
sides of the fixed saw table (8). Insert the clamping
device (15) into the hole provided on the rear side of
the stop rail (6) and secure it with the screw.
• Attach the workpiece supports (7) to the fixed saw
table (8) as shown in Fig. 6, 7 & 8 and push all
the way through. Secure the shafts with the lock-
ing screws to prevent them from slipping out ac-
cidentally.
www.scheppach.com