Transport; Working Instructions - Scheppach 4901305901 Originalbetriebsanleitung

Fig. 13
After adjusting the riving knife, refit the saw blade in-
sert (19) with 4 M6 x 16 flange head screws.
Fig. 14
Fit the cover hood (20) to the splitting wedge (18) with a
round-headed M6 x 25 screw, washer 6 and M6 wing nut.
Fig. 15
Connect the suction hose (21) to the suction hood (20)
and the suction port.
Connecting the chip extraction system, Fig. 15
m WARNING
Risk of eye injury from swirling chips
• Wear safety goggles.
• Only operate the product with a suitable chip extrac-
tion system. Do not use household vacuum cleaners.
1. Connect a suitable chip extraction system (not in-
cluded in the scope of delivery) to the suction port.
The chip extraction system must fulfil the following re-
quirements:
• Extraction port diameter: Ø100mm
• Necessary air volume flow: at least 460 m³/h
• Negative pressure: min. 530 Pa
• Recommended air speed: min. 20 m/s
ATTENTION
Check and clean the suction channels at regular inter-
vals.
Fig. 16 / 16.1
Fasten the hook bolt with 2 washers 6, 2 M6 nuts on
the right frame leg side. The saw blade key and the
push stick are hung on it.
The two transport handles are mounted on the front of
the saw, on the left and right legs with 4 M6 x 16 hex-
agonal bolts, 4 washers 6, 4 M6 nuts.
Fitting the longitudinal stop, Fig. 17 / 17.1
Connect the bearing piece to the clamping plate. Mount
the clamping plate to the tabletop with 2 M6 x 30 cylinder
screws, 2 A 6.4 serrated washers and 2 hexagonal nuts.
Installing the stop rail, Fig. 18
Mount the intermediate plate to the rip fence with 2 M6
x 50 flat round screws, 2 A 6 washers and 2 wing nuts.
Slide the stop rail onto the intermediate plate and
clamp it with the wing nuts.
Legend:
1 = High contact surface
2 = Low contact surface
To clamp, pull the clamping flap up; to release, press
it down.
Saw blade replacement, Fig. 19
Attention! Pull out the mains plug and wear protective
gloves.
Loosen the wing screw from the suction hood (20) and
remove it.
Fig. 20
Loosen the 4 Phillips screws from the table inlay (19)
and remove it.
Fig. 21
Set the saw blade all the way up and loosen the screw
with the saw blade key.
Attention! Left-handed thread
Fig. 22
Remove the saw blade flange (31) and then the saw
blade (32).
Now change the saw blade.
When mounting the saw blade flange, pay attention to
the recess.
After changing the saw blade, check the riving knife set-
ting and refit the table inlay (19) and suction hood (20).

8. Transport

The machine may only be transported with a suitable lift-
ing device (crane or forklift). The attachment point for the
rope (crane) is located on the upper belt wheel housing.
Do not lift the machine by the saw table.
By lifting at the front of the machine, it can be easily
relocated in the workshop area to suit the space re-
quirements.
9.

Working instructions

After every new setting, we recommend performing a
test cut, in order to check the dimensional settings.
After switching on the saw, wait until the saw blade has
reached its max. speed before making the cut.
Secure long workpieces against tipping at the end of
the cutting process (e.g. with roller stand, etc.).
Be careful when cutting in.
www.scheppach.com GB | 33