Transport - Scheppach Hbs400 Originalbetriebsanleitung

• Attention! Excessively high tension leads to prema-
ture breakage!
• Fit the table width extension in reverse order. (Fig.
K - O)
• On completion of work, always relieve tension on the
saw blade! To do this, loosen the tensioning screw (11).
8.8 Speed setting (Fig. V + W + X)
Pull out the mains plug!
• Open the lower protective cover.
• Release the tension on the belt with the tensioning
screw (12).
• Move the belt to the desired position (S1 or S2).
• Tension the belt again with the tensioning screw
(12).
• Close the lower protective cover.
Speed range:
• Speed stage 1 360 m/min.
- For processing hardwood, materials similar to
hardwood and for fine cuts.
• Speed stage 2 720 m/min.
- For processing softwoods and for less fine cuts.
8.9 Saw band guide (Fig. Y)
By loosening the locking knob (13), the saw band guide
can be adjusted.
The upper saw band guide can be set from 0 - 175 mm
workpiece height.
The smallest possible distance to the workpiece en-
sures optimal belt guidance and safe working!
Counterpressure bearings (Fig. Z + AA)
The counterpressure bearings (y) absorb the feeding
pressure of the workpiece. Adjust the top and bottom
counter pressure bearing so that it lightly touches the
back of the saw band. Tighten the screws (aa). The dis-
tance should be at least 0.5 mm.
Top guide rollers. (Fig. Z)
Adjust the top guide rollers (z) to the respective saw band
width. The front edges of the guide rollers must not extend
further than the tooth base of the saw band. If the guide
rollers lightly touch the saw band, tighten the screws (aa).
Bottom guide fingers (Fig. AA)
Adjust the bottom guide fingers (ab) to the respective
saw band width. The front edges of the guide fingers
may only reach up to the tooth base of the saw band. If
the guide fingers lightly touch the saw band, tighten the
adjusting screws (ac).
The saw band must not jam!
Storage of the push stick (Fig. AB)
In order to have the push stick (ae) to hand at all times,
hang it on the device (ad) intended for this, at the top
left side of your band saw.
8.10 Mitre gauge (14) (optional) (Fig. AC)
• Slide lateral stop (aj) into a groove (af) in the saw
bench.
• Loosen the grip screw (ag).
• Turn the lateral stop (aj) until the desired angular di-
mension has been set. The arrow on the lateral stop
indicates the set angle.
• Retighten the grip screw (ag).
• The stop rail (ai) can be slid against the lateral stop
(aj). To do so, loosen the knurled screw (ah) and
slide the stop rail (ai) into the desired position. Tight-
en the knurled screws (ah) again.
• Attention! Do not slide the stop rail (ai) too far in the
direction of the saw blade.
8.11 Switching on/off (Fig. A)
• It is possible to switch the saw on by pressing the
green "I" button (10). Before starting sawing, wait
until the saw blade has reached its maximum speed.
• In order to switch the saw off again, it is necessary to
press the red "0" button (10).
Attention!
All protective devices and covers must be installed be-
fore any work is carried out on the machine. The top
and bottom band wheel is clad by a firmly attached pro-
tection and a moveable housing cover. The machine is
switched off when the housing cover is opened. It can
only be switched on with the cover closed.
9.

Transport

Caution: Pay attention to the weight of the machine
when lifting it and call upon the help of another person!
Use the transport equipment. Stand on the side of the
wheels. Pull the upper part of the machine towards you
so that the machine stands on the two wheels and can
be moved. Hold the machine by its frame (9).
Attention! Note the high centre of gravity of the
machine.
Attention! Never use separating safety guards to
lift or transport the unit.
www.scheppach.com GB | 31