Scheppach HM254 Originalbetriebsanleitung Seite 35

– Points of sale of electrical devices (stationary and
online), provided that dealers are obliged to take
them back or offer to do so voluntarily.
– Up to three waste electrical devices per type of de-
vice, with an edge length of no more than 25 centi-
metres, can be returned free of charge to the man-
ufacturer without prior purchase of a new device
from the manufacturer or taken to another autho-
rised collection point in your vicinity.
– Further supplementary take-back conditions of the
manufacturers and distributors can be obtained
from the respective customer service.
17 Troubleshooting
The following table shows fault symptoms and describes remedial measures in the event of your product failing to work
properly. If you cannot localise and rectify the problem with this, please contact your service workshop.
Fault
Motor does not work
The engine runs slowly and
does not reach the operating
speed.
Engine producing excessive
noise.
The engine does not reach
full power.
Motor overheats easily.
Saw cut is rough or wavy.
Workpiece pulls away and/or
splinters.
18 EU Declaration of Conformity
Translation of the original Declaration of Conformity
Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
We declare under our sole responsibility that the product
described here complies with the applicable directives
and standards.
Brand: SCHEPPACH
Art. designation: Sliding cross-cut mitre saw -
HM254/HM254SPX/MST254
Art. no. 5901233901, 5901216984,
5901252901,
5801217930
EU directives:
2014/30/EU, 2006/42/EG, 2011/65/EU*,
* The object of the declaration described above fulfils the
regulations of the directive 2011/65/EU of the European
Parliament and Council from 8th June 2011, on the re-
striction of the use of certain hazardous substances in
electrical and electronic equipment.
Possible cause
Engine, cable or connector defective,
mains fuses blown.
Voltage too low, coils damaged, ca-
pacitor burnt.
Coils damaged, motor defective.
Circuits in the network are overloaded
(lamps, other motors, etc.).
Overloading of the motor, insufficient
cooling of the motor.
Saw blade dull, tooth shape not ap-
propriate for the material thickness.
Excessive cutting pressure and/or saw
blade not suitable for use.
www.scheppach.com
• If the manufacturer delivers a new electrical appliance
to a private household, the manufacturer can arrange
for the free collection of the old electrical appliance
upon request from the end user. Please contact the
manufacturer's customer service for this.
• These statements only apply to devices installed and
sold in the countries of the European Union and which
are subject to the European Directive 2012/19/EU. In
countries outside the European Union, different regu-
lations may apply to the disposal of waste electrical
and electronic equipment.
Remedy
Arrange for inspection of the product by a special-
ist. Never repair the motor yourself. Danger!
Check mains fuses and replace as necessary
Have an electrician check the voltage. Arrange for
inspection of the motor by a specialist. Arrange
for replacement of the capacitor by a specialist.
Arrange for inspection of the motor by a special-
ist.
Do not use any other products or motors on the
same circuit.
Avoid overloading the motor while cutting, remove
dust from the motor in order to ensure optimal
cooling of the motor.
Resharpen saw blade and/or use suitable saw
blade.
Insert suitable saw blade.
Applied standards:
EN 62841-1:2015/A11:2022;
EN IEC 62841-3-9:2020/A11:2020;
EN IEC 55014-1:2021; EN IEC 55014-2:2021;
EN IEC 61000-3-2:2019/A2:2024;
EN IEC 61000-3-3:2013/A2:2021
Documentation authorised representative:
Georg Kohler
Günzburger Str. 69
D-89335 Ichenhausen
Ichenhausen, 08.05.2026
Simon Schunk
Division Manager Product Center
Andreas Pecher
Head of Project Management
GB | 35