Operation; Working Instructions; Suction Function; Electrical Connection - Scheppach 5906301901 Originalbetriebsanleitung

8.4 Storing the nozzles (8/9/10) and
suction hose (2b) (Fig. 8)
1. You can store the nozzles (8/9/10) in the container
(2e) inside the product.
2. You can store the suction hose (2b) in the holder (2d)
on the cover (2).
8.5 Using the various nozzles (8/9/10)
(Fig. 10, 11)
Blast nozzle (8):
• Blasting off surfaces.
• Inflating suitable objects with a compatible valve.
• The air flow can be regulated by covering the hole in
the blast nozzle (8).
Drilling suction nozzle (9):
• Collects dust generated directly at the drilling site.
• The drilling extraction nozzle (9) adheres to flat sur-
faces by itself due to the negative pressure created
during suction.
Joint nozzle (10):
• Suctioning out hard-to-reach areas.
8.5.1 Fitting the nozzle (Fig. 10)
1. Fit the desired nozzle (8/9/10) onto the suction hose
(2b).
2. Remove the nozzle (8/9/10) by pulling it forward off
the suction hose (2b).
9

Operation

WARNING
Danger of injury!
Do not insert the mains plug into the socket until you
are ready to use the product.
ATTENTION
Always make sure the product is fully assembled
before commissioning!
9.1 Switching the product on/off
(Fig. 1)
Switching on
1. Insert the mains plug into a properly fused socket.
2. Switch the product on by pressing the on/off switch (1).
Switching off
1. Switch off the product by pressing the on/off switch (1)
again.

10 Working instructions

10.1

Suction function

WARNING
Vacuuming glowing ash as well as flamma-
ble, hazardous substances is prohibited.
There is a danger of injury!
ATTENTION
Fine dusts, such as those from cement, soot and plas-
ter, are too fine to be absorbed. There is a risk that it
could get into the motor and damage it.
ATTENTION
Do not use without a filter!
• Place the product on a level, even surface.
• Do not suck up any hot, glowing, flammable, explosive
or hazardous substances. These include hot ash, pet-
rol, solvents, acids or alkalis.
There is a risk of fire and injury.
• If the products heats up switch the product off and pull
out the mains plug. Let the product cool down out-
doors under supervision.
10.2 Blast function
WARNING
Danger of injury!
If you direct the airflow at people, animals or objects,
this can cause injury and damage.
– Direct the air flow away from you.
– Never direct the airflow at other people, animals or
objects.
– Do not blow away hard objects such as stones or
branches.

11 Electrical connection

The connection complies with the applicable national
provisions.
Connections and repair work on the electrical equipment
may only be carried out by electricians.
• Before commissioning, ensure that the mains voltage
matches with the operating voltage on the type plate.
• Pay attention to the manufacturer's instructions when
using extension cables.
11.1 Damaged electrical connection
cables
The insulation on electrical connection cables is often
damaged.
This may have the following causes:
• Pressure points, where connection cables are passed
through windows or doors,
• Kinks where the connection cable has been improper-
ly fastened or routed,
• Places where the connection cables have been cut
due to being driven over,
• Insulation damage due to being ripped out of the wall
socket,
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation dam-
age.
www.scheppach.com GB | 19