Additional Safety Rules - Makita 3703 Betriebsanleitung

ENGLISH
1 Loosen
2 Tighten
3 Hold
4 Base
5 Adjusting screw
6 Bit protrusion
7 Nut
8 Scale
9 Switch lever
10 Workpiece
11 Feed direction
12 Bit revolving direction
13 View from the top
of the tool
SPECIFICATIONS
Model
Collet chuck capacity ................................. 6 mm or 1/4''
-1
No load speed (min ) .......................................... 30,000
Overall length ..................................................... 247 mm
Net weight ............................................................. 1.5 kg
• Due to the continuing program of research and devel-
opment, the specifications herein are subject to change
without prior notice.
• Note: Specifications may differ from country to country.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
Safety hints
For your own safety, please refer to enclosed safety
instructions.

ADDITIONAL SAFETY RULES

1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool
may contact hidden wiring or its own cord. Con-
tact with a ''live'' wire will make exposed metal
parts of the tool ''live'' and shock the operator.
2. Wear hearing protection during extended period
of operation.
3. Handle the bits very carefully.
4. Check the bit carefully for cracks or damage
before operation.
Replace cracked or damaged bit immediately.
5. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
6. Hold the tool firmly.
7. Keep hands away from rotating parts.
8. Make sure the bit is not contacting the workpiece
before the switch is turned on.
9. Before using the tool on an actual workpiece, let it
run for a while.
Watch for vibration or wobbling that could indi-
cate improperly installed bit.
10. Be careful of the bit rotating direction and the
feed direction.
11. Do not leave the tool running. Operate the tool
only when hand-held.
6
Explanation of general view
14 Correct bit feed direction
15 Trimmer shoe, straight guide or
trimmer guide
16 Bolt
17 Guide plate
18 Straight guide
19 Flat washer
20 Wave washer
21 Wing nut
22 Clamp screw (A)
23 Center hole
24 Nail
25 Adjusting screw
12. Always switch off and wait for the bit to come to a
3703
13. Do not touch the bit immediately after operation;
14. Always lead the power supply cord away from the
15. Do not smear the tool base carelessly with thin-
16. Draw attention to the need to use cutters of the
SAVE THESE INSTRUCTIONS.
OPERATING INSTRUCTIONS
Installing or removing trimmer bit (Fig. 1)
Important:
Always be sure that the tool is switched off and unplugged
before installing or removing the bit.
ENB054-1
Insert the bit all the way into the collet cone and tighten
the collet nut securely with the two wrenches. To remove
the bit, follow the installation procedure in reverse.
CAUTION:
• Do not tighten the collet nut without inserting a bit, or the
collet cone will break.
• Use only the wrenches provided with the tool.
Adjusting bit protrusion (Fig. 2)
To adjust the bit protrusion, loosen the nut and move the
tool base up or down as desired by turning the adjusting
screw. After adjusting, tighten the nut firmly to secure the
tool base.
Switch action (Fig. 3)
To start the tool, move the switch lever to the ''ON''
position. To stop, move the switch lever to the ''OFF''
position.
Operation
• Set the tool base on the workpiece to be cut without the
bit making any contact. Then turn the tool on and wait
until the bit attains full speed. Move the tool forward
over the workpiece surface, keeping the tool base flush
and advancing smoothly until the cutting is complete.
26 Clamp screw (B)
27 Trimmer guide
28 Bit
29 Guide roller
30 Screwdriver
31 Base protector
32 Screws
33 Straight bit
34 Templet
35 Distance (X)
36 Templet guide 10
37 Limit mark
38 Brush holder cap
complete stop before removing the tool from
workpiece.
it may be extremely hot and could burn your skin.
tool towards the rear.
ner, gasoline, oil or the like.
They may cause cracks in the tool base.
correct shank diameter and which are suitable for
the speed of the tool.