Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
BR
BD
Set the drive di-
Observe the
rection using
display and wait
the drive direc-
till the controls
tion button at
are initialized.
the operator
Set the drive di-
console.
rection using
Select speed
the drive direc-
range using the
tion button at
speed button (3
the operator
stages).
console.
Select speed
range using the
speed button (3
stages).
Press the unlocking key.
Press the accelerator carefully to drive.
Note
The drive direction can also be changed
during the drive. You can thus clean very
dirty surfaces by driving back and forth a
couple of times.
Overload
In case of overloading, the drive motor auto-
matically switches off after a certain period.
Allow machine to cool down at least for
15 minutes.
Press again the drive fuse on the oper-
ating panel.
Cleaning
BR
BD
Press down-
Press Cleaning
ward the lever
operations key.
for lowering the
The brush drive
vacuum bar.
is activated.
The varuum bar
The cleaning
is lowered and
head is lowered
the suction is
(slight brush
activated.
contact pres-
Lower the
sure) and the
cleaning head
detergent liquid
by pressing the
is supplied.
button for brush
The varuum bar
contact pres-
is lowered and
sure.
the suction is
activated.
Note
The detergent supply and brush drive are
interrupted till further movement if the de-
vice stands at one place for more than 2
seconds.
Press accelerator pedal and drive to the
surface to be cleaned.
BR
BD
Adjust the de-
Adjust the de-
tergent flow us-
tergent flow us-
ing the water
ing the Dosing
regulation
Liquid Deter-
knob.
gent switch (4
stages).
Adjust brush contact pressure using the
Brush Contact Pressure switch (4 stages).
BR
BD
Select speed
Select speed
range using the
range using the
speed button (3
speed button (3
stages).
stages).
In cleaning mode, the highest speed is lim-
ited to Stage II.
Note
Very dirty floors can be cleaned in two
rounds. In the first work step, the detergent
liquid is applied and brushed in. The vacu-
um bar is raised by pressing the Raise/Low-
er Vacuum Bar switch. In the BD model,
the rear spray guard (Aqua-Mizer) also
needs to be removed. The surface is
cleaned normally in the second step after
the detergent has worked normally.
Complete cleaning
BR
BD
Raise the
Press Cleaning
cleaning head
operations key.
by pressing the
The brush drive
Brush Contact
is switched off
Pressure
and the clean-
switch.
ing head is
Pull the vacuum
raised.
bar lowering le-
The vacuum
ver upward; the
bar is raised af-
vacuum bar is
ter 15 seconds.
raised and the
The suction is
suction is
switched off af-
switched off.
ter 30 seconds.
Note
After raising the cleaning head, drive further
approx. 5 m so that the remaining water is
sucked off.
Shutting down
Park the machine on an even surface.
Turn key to "0" and remove it.
Empty tanks.
Drain off dirt water
Note
Overflow dirt water tank. The suction flow is
interrupted by the swimmer when the dirt wa-
ter tank is full. Empty the dirt water reservoir.
Warning
Please observe the local provisions regard-
ing the wastewater treatment.
Take the dirt water discharge hose from
the support and lower above a suited
collection device.
Let off dirt water by opening the screw
lid at the discharge hose.
Rinse the dirt water tank with clear wa-
ter.
Clean the swimmer and check the
movement of the swimmer ball.
Rinse the dirt water tank with clear wa-
ter.
Drain off clean water
Pull out the drain hose for fresh water
(located behind the drain hose for dirt
water) and lower it into a suitable collec-
tion system.
Let off detergent by opening the screw
lid at the discharge hose.
Emptying waste container
(only BR model)
Lift the cleaning head.
Turn key to "0" and remove it.
Loosen the cross-handle of the spray
guard and tilt the spray guard to the
side.
Remove the waste container.
Empty the waste container and rinse
with water.
Transport
Danger
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients of max. 2%. Drive slowly.
Remove vacuum bar, brushes and
spray guard from the device.
If you want to transport the machine on
a vehicle secure it from slipping using
belts/ ropes.
1 Fastening points
Maintenance and care
Danger
Risk of injury! Before carrying out any tasks
on the machine, set the main key to "0" and
remove it. Pull out the battery plug.
English
19
Quicklinks ausblenden:
Werbung
Kapitel
Inhaltsverzeichnis
