Shutting Down The Appliance . En; Transport; Storage; Care And Maintenance - Kärcher BD 43/25 C Classic Bp Pack 80 Ah Li Bedienungsanleitung

Removal of coating from all al-
kali-resistant floors (e.g. PVC)
Removal of coating from li-
noleum floors
 Add the detergent to the fresh water
reservoir.
Note:
If the fresh water tank is empty, the cleaning
head continues working without liquid supply.
Setting the water quantity
 Adjust the water quantity using the reg-
ulating button according to the dirt on
the floor covering.
Note:
Carry out initial cleaning attempts with low
water volume. Increase water volume step-
by-step until the desired cleaning result is
achieved.
Setting the Vacuum Bar
Oblique position
To improve the vacuuming result on tiled
floors the vacuum bar can be turned to an
oblique position of up to 5°.
 Loosen the wing nuts.
 Turn the vacuum bar.
 Tighten the wing screws.
Inclination
If the vacuum result is unsatisfactory the in-
clination of the straight vacuum bar can be
modified.
 Adjust the rotary handle to incline the
suction bar.
Height
The bend of the suction lips upon contact
with the floor is influenced with the height
adjustment.
 Try adjusting the twist handles of the
height adjustment until the best vacu-
uming result is achieved.
14
RM 752
ATTENTION
RM 754
Risk of damage to the floor covering. Do
not operate the appliance on the spot.
 Turn the program selection switch to
the desired cleaning program.
Lower the vacuum bar
 Pull the lever out and press it down; the
vacuum bar is lowered.
Note:
– For cleaning tiled floors, adjust the
straight suction bar in such a way that
cleaning is not done at an angle of 90
degrees to the joints.
– The inclined position and the inclination
of the suction bar can be adjusted to
achieve better suction results (see "Ad-
justing the suction bar").
– If the waste water tank is full, the float
closes the suction opening and the suc-
tion turbine runs at an increased speed. If
this is the case, shut the vacuum off and
drive to empty the waste water tank.
Shutting Down the Appliance
 Release the safety switch.
 Set the program selection switch to suc-
tion or vacuuming.
 Briefly drive forward and suck of the re-
maining water.
 Raise the vacuum bar.
 Charge battery, if required.
WARNING
Please observe the local provisions regard-
ing the wastewater treatment.
 Take the water discharge hose from the
support and lower above a suited col-
lection device.
 Crush or bend the dosing equipment.
 Open the lid of the dosing equipment.
 Drain off the dirt water - regulate the
water quantity by pressing or bending.
 Rinse the waste water tank with clear
water.
Drain off clean water
 Unscrew the lock of the fresh water res-
ervoir.
Cleaning
Drain off dirt water
4
-
EN

Transport

DANGER
Risk of injury! When loading or unloading
the machine, it may only be operated on
gradients up to the maximum value (see
"Technical Specifications"). Drive slowly.
CAUTION
Risk of personal injury or damage! Mind the
weight of the appliance during transport.
 Use the pushing handle to push the ap-
pliance.
 When transporting in vehicles, secure
the appliance according to the guide-
lines from slipping and tipping over.

Storage

CAUTION
Risk of personal injury or damage! Consider
the weight of the appliance when storing it.
This appliance must only be stored in inte-
rior rooms.

Care and maintenance

DANGER
Risk of injury! Set the programme selector
switch to "OFF" and pull the mains plug of
the charger prior to performing any work on
the appliance.
Remove the battery plug from machine.
 Drain and dispose of the dirt water and
the residual fresh water.
Maintenance schedule
After each operation
ATTENTION
Risk of damage. Do not sluice the appli-
ance with water and do not use aggressive
detergents.
 Drain off dirt water.
 Rinse the waste water tank with clear
water.
 Clean the outside of the appliance with
a damp cloth which has been soaked in
mild detergent.
 Check the fluff filter, clean if required.
 Clean the vacuum lips and the wiping
lips, check for wear and replace if re-
quired.
 Check the brush for wear and replace if
required (see "Maintenance tasks").
 Charge the battery if required.
Weekly
 When used regularly, charge the bat-
tery fully and without interruption at
least once a week.