Transporting The Equipment (Fig. 24); Maintaining The Equipment; Carbon Brushes - Scheppach Hs80 Original Bedienungsanleitung

2. Use the push block to press the workpiece against
the stop rail and push the workpiece with the push
stick (14) through to the end of the splitter.
10.1.3 Making angular cuts (fig. 22)
Angular cuts must always be made using the parallel
stop (7).
The parallel stop (7) must always be fitted to the right
of the saw blade. Otherwise, workpieces can become
jammed between the parallel stop and the saw blade
during sawing and ejected at speed.
1. Set the saw blade (5) to the desired angle (see 9.3).
2. Set the parallel stop (7) in accordance with the
workpiece width and height (see 9.4).
3. Carry out the cut in accordance with the workpiece
width (see 10.1).
10.2 Making transverse cuts (fig. 23)
1. Push the transverse stop (2) into the groove (40)
of the saw table and set it to the required angle
(see 9.5).
2. Use the stop rail (17).
3. Press the workpiece firmly against the transverse
stop (2).
4. Switch on the saw.
5. Push the transverse stop (2) and the workpiece
toward the saw blade (5) in order to make the cut.
m WARNING: Always hold the guided part of the work-
piece. Never hold the part which is to be cut off.
6. Push the transverse stop (2) forward until the
workpiece is cut all the way through.
7. Switch off the saw again.
8. Do not remove the offcut until the saw blade has
stopped rotating.
10.3 Cutting particle boards
To prevent the cutting edges from cracking when work-
ing with particle boards, you should not set the saw
blade (5) more than 5 mm greater than the thickness of
the workpiece (also see 9.2).

11. Transporting the equipment (fig. 24)

• Turn off the power tool before any transport and dis-
connect it from the power supply.
• Lower the saw blade (5) as far as possible.
• Wind up the mains cable (41).
• Carry the power tool with both hands by the fixed
saw table (1). Never use the table width extension to
carry the power tool.
40 | GB
• Protect the power tool from knocks, bumps and strong
vibrations, such as during transport in vehicles.
• Secure the power tool against overturning and slid-
ing.
• Never use the safety devices for handling or trans-
porting purposes.

12. Maintaining the equipment

m WARNING: Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
12.1 General maintenance measures
• Keep protective devices, air vents, suction openings
and the motor housing as free of dust and dirt as
possible. Remove shavings and dust with a vacu-
um cleaner and a brush. In addition, blow it out with
low-pressure compressed air.
• We recommend that you clean the equipment imme-
diately after you use it.
• Clean the equipment regularly with a damp cloth and
some soft soap. Do not use cleaning agents or sol-
vents; these may be aggressive to the plastic parts
in the equipment.
Ensure that no water can get into the interior of the
equipment.
• In order to extend the service life of the tool, oil the
rotary parts once monthly. Do not oil the motor.

12.2 Carbon brushes

• In case of excessive sparking, have the carbon
brushes checked only by an electrical specialist.
IMPORTANT: The carbon brushes must not be re-
placed by anyone but an electrical specialist.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the following
parts are therefore also required for use as consum-
ables.
Wear parts*: carbon brushes, table inlay, push stick,
saw blade
* Not necessarily included in the scope of delivery!
Spare parts and accessories can be obtained from our
service centre. To do this, scan the QR code on the
cover page.
www.scheppach.com