Werbung
CD PLAYER
Selecting a desired track
Selecting a desired track at the stop mode
1 Press S or T ( PREV ¡ or NEXT ™ on
CD
the remote control) until the desired track
appears on the display.
TUNER
2 Press PLAY B on the set or remote control to
start playback.
CD
– The selected track number and elapsed
playing time appear on the display.
TUNER
Selecting a desired track during play mode
1 Press S or T ( PREV ¡ or NEXT ™ on
CD
the remote control) until the desired track
appears on the display.
TUNER
– The selected track number and elapsed
playing time appear on the display.
• If you press S once it will skip to the begin-
ning of the current track and play the track
again.
CD
Searching for a particular passage
TUNER
during playback
• Press and hold S or T (5 or 6 on the
remote control) until the desired passage is
CD
located.
TUNER
– During the search, the sound is played at a
faster than normal rate and at a reduced
volume.
– Playback returns to normal when S or
T is released.
CLOCK SETTING
MULTI FUNCTIONAL DISPLAY
CD
DEMO
A
TUNER
N/OFF
STAND BY
CLOCK
TIMER
ON/OFF
VOLUME
Setting the clock
The clock will display in 24-hour mode, e.g.
00:00 or 23:59.
CD
1 Press ON/OFF to switch on the set.
TUNER
2 Press CLOCK
˚
.
– "0:00" appears and the first "0" starts
flashing.
3 Set the hour with A or B.
CD
4 Press S or T to switch to the minute
mode. ":00" starts flashing.
TUNER
5 Set the minute with A or B.
˚
6 Press CLOCK
again to store the setting.
– The clock starts running.
CD
Note: When a power interruption occurs, the
clock setting is erased, and "0:00" will
TUNER
flash on the display.
CD
TUNER
Changing the display mode
during playback
You can change to a different type of time
display when the CD is playing.
• Press (or DISPLAY on the remote control) to
cycle through the various time display modes.
– The display will show :
Elapsed playing time of the current track –>
Remaining playing time of the current track –>
Remaining playing time of CD –> ...
Shuffle
SHUFFLE – playing all the tracks in random order.
It can also be used when tracks are
programmed.
SHUFFLE
To shuffle all the tracks
1 Press CD ( SHUFFLE ) (or SHUFFLE on the remote
control).
– "SHUFFLE" scrolls once on the display.
– The
flag and the track selected at
SHUFFLE
SHUFFLE
random appear on the display.
• The tracks will now be played in random
order until you press STOP 9 or until all the
tracks have been played once
2 Press CD ( SHUFFLE ) again to resume normal
playback.
– The
flag disappears from the display.
SHUFFLE
TIMER SETTING
Setting the Timer
• The system can switch on to TUNER, CD, TAPE
or REC TU mode automatically at a preset
time.
It can serve as an alarm to wake you up.
One hour after the preset time, the system will
return to the standby mode if no button is pressed.
• Before setting the timer, make sure the clock is
set correctly.
• The timer setting will remain active until you
reset it.
• The volume of the timer will be at the last
setting before the set is switched to standby
mode.
Timer Setting
1 Press ON/OFF to switch on the set.
˚
2 Press TIMER
/
and hold for 2
ON
OFF
seconds.
– The
flag flashes.
TIMER
3 Press A or B to select the desired source.
– TUNER, CD, TAPE or REC TU.
3a If you select TUNER...
you should first select the desired waveband
(MW or FM) and then press PRESETA or B
TIMER
to select the preset station.
•
Then, continue with steps 4 to 8.
3a If you select CD...
track 1 will be selected and playback starts
automatically at the preset time.
TIMER
•
Continue with steps 4 to 8.
3a If you select TAPE...
tape playback will start automatically at the
preset time.
•
Continue with steps 4 to 8.
CD PLAYER
Programming Tracks
Programming tracks of a loaded CD is possible in
the stop mode of the CD. The display will indicate
the total tracks stored in the program. Up to 20
tracks can be stored in the memory in any order.
When 20 tracks are stored and you attempt to store
another track, the display will show "PROGRAM
FULL".
1 Load the desired disc in the disc tray.
2 Press S or T ( PREV ¡ or NEXT ™ on
the remote control) to select the desired track.
3 Press PROG. to store the track.
• Repeat steps 2 and 3 to store other discs and
tracks.
CD
Playing the program
1 Press PLAY B on the set or remote control to
TUNER
start program playback.
– "PROGRAM PLAY" scrolls once on the
CD
display.
– The track number and elapsed playing time of
TUNER
the current track will appear on the display.
2 Press STOP 9 on the set on the remote control
to stop program playback.
Erasing the program (in the stop position)
CD
• Press STOP 9.
– The last stored track is erased.
TUNER
– "CLEARED" appears on the display.
• Press and hold STOP 9 for 2 seconds.
CD
– All the programmed tracks are erased.
– "PROGRAM CLEARED" appears on the
display.
TUNER
Note : The program is also erased when the set
is disconnected from the power supply or the CD
tray is opened.
TIMER SETTING
3a If you select REC TU...
a blank tape has to be inserted into the
cassette compartment.
Press PRESETA or B to select the preset
•
station to be recorded.
CD
•
Then, continue with steps 4 to 9.
FM
˚
4 Press TIMER
/
to confirm your
TUNER
ON
OFF
selection.
– " START " is displayed.
– The display shows " 0:00 " and "00"
flashes.
5 Press A or B to set the hour for the timer to
start.
6 Press S or T to switch to the minute
mode.
7 Press A or B to set the minutes for the timer
CD
to start.
FM
8 Press TIMER
˚
/
to store the start time.
TUNER
ON
OFF
9 If you have selected REC TU, you should also
adjust the stop time. " STOP " is displayed.
CD
• Adjust the stop time in the same way as the
˚
start time and press TIMER
/
to store
ON
OFF
FM
TUNER
the stop time.
– The TIMER is now set and the
flag
TIMER
remains lit.
To stop the timer
CD
˚
• Press TIMER
/
on the set.
ON
OFF
FM
– The
flag disappears from the display.
TUNER
TIMER
To start the timer again
˚
• Press TIMER
/
.
ON
OFF
– The
flag appears again on the display.
TIMER
Notes: When no button is pressed for 10
seconds, the set will automatically leave the timer
setting mode.
CD Synchro Start Recording
1 Load a blank cassette into the cassette deck.
2 Press TAPE ( ∫ ) or SIDE on the remote
control to select the play mode ( å or ∂ ).
3 Select side A or B of the cassette.
– The A or B flag appears in the display,
depending on the side selected.
4 Press CD on the set or remote control to select
the CD mode.
5 Load a disc into the disc tray.
6 You can program the tracks in the order you
want them to be recorded (see Programming
Tracks). If not, the tracks are recorded
RECORD
according to the selected disc.
7 Press REC 0 to start recording.
– "ONE TOUCH RECORDING" scrolls once on
the display.
RECORD
– The
flag appears.
RECORD
– The CD starts playing after a seven-second
delay to prevent recording on the leader tape
at the beginning of the tape.
8 Press STOP 9 to stop recording.
OTHER FEATURES
Mute
This feature allows you to temporarily switch off
the sound of the system without switching off the
set when you require a moment of silence.
• Press MUTE on the remote control to switch off
DBB
the sound.
– "MUTE" is displayed.
STEREO
TUNED
PRESET
• Press MUTE again on the remote control to
switch on the sound.
Sleep
This feature allows you to select a time after
which the system will switch to the standby mode
automatically.
• Press SLEEP on the remote control repeatedly
DBB
to cycle through the sleep timer mode.
– "SLEEP" and the
flag are displayed.
SLEEP
STEREO
TUNED
PRESET
– The timer for selection is as follows:
120 MIN –> 90 MIN –> 60 MIN –> 45
MIN –> 30 MIN –> 15 MIN –> 5 MIN –>
DBB
OFF –> 120 MIN ...
STEREO
• Select the sleep time you desire.
TUNED
PRESET
When the sleep timer is switched on, to check
the remaining time before the set switches to
standby mode.
DBB
• Press SLEEP once.
– The remaining time will scroll through the
STEREO
TUNED
PRESET
display.
To switch off the sleep timer mode.
• Press SLEEP until "OFF" is displayed or
press y.
Werbung
