Herunterladen Diese Seite drucken

Lorelli INFINITY Bedienungsanleitung Seite 15

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 54
Adjusting
the height
1. Release the shoulder
(Figure 3)
2. Unclip the strap buckles from the centre buckle and pull the two straps from the back of the backrest,
move them to the next position.
Fastening
the harness.
I . Connect the two elements "E" and "F" at the end of the strap (Figure 5) and place them in the central buckle
"3" until
a click
is heard.
2. Make sure the harness is locked by pulling the shoulder straps up. (Figure 6)
3. To release the harness, press down the red button on the central buckle "3". (Figure 7)
Adjusting
the length of the straps.
I . Releasing the straps: Press the strap adjustment
(Figure 3)
2. Tightening the straps: Place the child in the seat, fasten the two straps in the centre buckle and pull the strap in
the middle of the seat "5". (Figure 8)
Upholstery
removal
held in place with plastic clips on each side of the car seat (Figure 17). For children weighing
seat should
be used with the padded liner. When the child's weight is between
remove the padded liner. Release the straps from the buckle and remove the padded liner.
Remove the canopy - Pull the small buttons on each side of the canopy and pull it out of the holder. (Figure 16)
Adjusting the handle for carrying the car seat
The handle for carrying the car seat can be adjusted in 4 positions.
To adjust the handle, press the red buttons on both sides ofthe handle at the same time and turn. (Figure 9)
Position
I - Forward-facing
the car. (Figure 10)
Position 2 - Upright - to carry.
Position
3 - Fixed horizontally
Position
4 - Down behind the back - Fixing the seat upright to feed the child.
Make sure the handle
fastened
before carrying
WARNING:
The car seat should
Installing - Hold the car seat facing the handle of the stroller. Place the car seat adapters (A) on the mounting
points (B). Position the car seat guides (A) above the mounting points (B) and press down until a "Click" is heard
- Figure 18. Pull up the car seat to make sure it is securely attached to the stroller frame.
Removal
- to remove the car seat, simultaneously
INSTALLATION OF THE SEAT "Group 0+" 1for newborns and weight up to 13 kg. 1
Please use the car's 3-point seat belts to ensure the safety of the child and secure the car seat!
Your car seat can be installed ONLY with using a 3-point belt and rear facing.
ATTENTION!
The car seat must not touch the front passenger
Step 1.Adjust the handle to front position. (Figure 10)
Step 2. Place the child seat on the car seat facing the rear, ensuring that it is snug against the backrest. The
car seat should only be used on the back seats of the car! (Figure 12)
Step 3. Pass the lap belt through the two guides on the sides ofthe child seat. (Figure 13) Fasten the seatbelt
the car buckle until a "click" is heard. Pull the shoulder strap up to tighten the child seat to the car seat and make
sure
the belt is fastened.
Step 4. Place the shoulder belt in the guide on the back ofthe child seat. (Figure 14)
Step 5. Pull the shoulder strap to tighten it.
Step 6. Ensure that the seat is securely fastened to the car seat and that the belt is taut and not twisted. (Figure
15)
Step 7. Place the child in the chair. Check the height of the shoulder
twisted or caught on anything.
strap in the centre of the seat to
of the straps.
straps
by pressing the belt adjustment
- To remove the seat upholstery,
- for installing in the car. Only this position can be used when the seat is installed in
behind the back - For rocking seat function.
is locked
in the selected
your child in the car seat.
INSTALLING
THE
only be installed
Fasten the child 's safety harness, making sure they are secure, and pull the
button "4" and pull on both shoulder straps at the same time.
first remove the harness. The upholstery
position,
the seat harness
CAR
SEAT
ON THE
facing the parents,
press the buttons on both sides and pull up - Figure 19.
15
button "4" and pulling the shoulder
10 kg and 13 kg, you must
is in place and the buckle
STROLLER
FRAME
as shown
in figure
seat.
(Figure
II)
straps. Make sure the belts are not
straps
then
of the seat is
up to 10 kg, the car
is
19.
in
loading