Lorelli INFINITY Bedienungsanleitung Seite 11

Picture I
I. Metal frame of the stroller
2. Shopping basket
3. Back wheels
4. Front wheels
5. Summer seat
6. Bumper bar
7. Canopy
1. Folded stroller (Figure 2)
2. Lift the handle of the stroller up, the stroller will unfold and lock in place automatically. (Figure 3)
1. Install the front wheels by pressing the console button and pushing them up until they lock in place (Figure 4).
Ensure that they ate securely
downwards. (Figure 5)
2. Install the rear wheels as shown in Figure 6 To remove, pull the rear axle button and pull the wheel off. (Figure
7)
3. Install the stroller seat in the frame as shown in Figure 8. If you hear a click, it means that the seat is fixed in
place. To remove, press the buttons on both sides of the seat at the same time and pull upwards (Picture 9). The
seat can be installed to face
4. Install the bumper bar. To remove the bumper bar, press the buttons on both sides and pull. (Figure 10)
5. The bottle holder is mounted on the right side ofthe frame. (Figure 11)
I. To lock the stroller in place, use the brakes on the rear wheels by pressing the brake pedal, located on the rear
axle (Figure 12) To release the brake, raise the brake pedal with your foot.
2. You can adjust the handle by pressing both buttons on the side and pushing up and down. (Figure 13)
3. While pushing the stroller on rough and uneven surfaces, you can use the straight-line option by pressing the
button to lock the front wheels. To release the front wheels, lift the lock button. (Figure 14)
4. To adjust (lower) the canopy, grab its upper part and pull it down to the desired position. (Figure 15)
5. When using the seat, it is MANDATORY
6. Attach the shoulder and abdominal straps and place them in the central locking buckle (Figure 16). Adjust the
length of the harness straps by pulling the buckles (Figure 17). To release the harness, press on the central
buckle button. (Figure 16)
7. Adjusting the footrest - To change the position of the footrest,
(Figure 18). ATTENTION!
will not be subject to warranty!
8. You can adjust the position of the backrest by pulling up the handle to unlock the mechanism located on the
back and placing it in the desired position. (Figure 19)
ATTENTION! If you try to adjust the backrest without unlocking the mechanism and apply excessive force, the
unlocking mechanism
Attention! The brake does not guarantee
stroller on an inclined surface with a child sitting or lying in the stroller!
WARNING! The brake on your stroller is a type of parking device. To activate the brake, the stroller must be
stationary. Carefully press the brake pedal, while gently pushing the stroller front-and-back to synchronize the
braking device and for more secure activation ofthe braking mechanism.
9. If you want, you can attach the footmuff
upholstery and the canopy.
- I pc.
-1 pc.
-2 pcs.
-2 pcs.
-1 pc.
-I pc.
- Ipc.
UNFOLDING
ASSEMBLING
locked in place. To remove,
the front or the rear.
EXPLOITATION
to put the child's safety harness on!
Failure to observe
may become deformed,
optimal power when on steep inclines! Therefore,
PARTS
8. Seat footmuff
9.Accessory bag
10. Pram body with mattress and carrying handle
II. Pram body cover
12. Pram body adapters
13. Car seat
14. Car seat adapters
15. Cup holder
press the console
press both buttons simultaneously
this instruction will damage
which is not subject to warranty!
to the seat by slipping
button and pull the wheel
the locking
it under the footrest and fastening
-1 pc.
- Ipc.
- I pc
-I pc.
- 2 pcs.
-1 pc.
-2 pcs.
-1 pc.
and adjust
mechanisms and
never leave the
to the