casco PF100 RESCUE Gebrauchsanweisung Seite 6

A: HELMET FITTING
1. Correct helmet size choice
The protective effect can only then be achieved when the CASCO helmet is optimally fitted and the head
ring correctly adjustedto headsize. Always wear the helmet in such a way that the size adjustment is
located at the rear. When worn, the helmet should feel safe and secure. In order to improve comfort still
further, please use the integrated size adjustment mechanism.
2. Adjusting the size adjustment mechanism
A snug fit is a prerequisite for ensuring maximum protection. Head ring adjustment to the appropriate
head size is achieved using the twistable clasp located at the neck. Rotation to the left opens or loosens
the head ring. Clockwise rotation to the right reduces the infinitely variable head ring in size (Fig. 1). In
addition, the headband can be adjusted to head size (Fig. 2).
3. Height adjustment
The interior lining of the helmet can be height adjusted. Remove the pins securing the carrying net and
re-affix at the desired height. On delivery, the height fixed for wear is in mid-position.
4. The correct helmet position
Always place the helmet horizontally on the head, angled to protect your forehead yet not to impair your sight.
Your helmet should not sit on the back of your head (Fig. 4).
5. Chin strap adjustment
Your CASCO helmet is equipped with the CASCO-Loc strap adjustment system (Fig. 5). Mount the CASCO-
Loc fastening onto the distributor ring. Draw the chin strap taught by pulling on the free end of the right
distributor. To loosen, swivel the distributor slightly upwards. To release, tug the pulling chord on the left
side directly away from your head.
Once the chin strap delivered by the producer has been properly attached, adjusted and worn in ac-
cordance with the required specifications, this helmet meets the European standards of securement.
6. Strap adjustment ‚Fixed Strap Comfort'
Your CASCO helmet has fixed strap comfort: the straps under the ear are firmly sewn on to the distributor.
There is no need to adjust the sides.
7. Verification of fit and securement of straps
Before using the helmet, ensure that it sits comfortably and that the straps are correcly adjusted and the
chin strap adequately tightened.
Verification of fit:
Using both hands, try to twist the helmet to the left and right. An optimum fit is when the skin on your
forehead moves with the helmet; if this is not the case, then the helmet is too loose. Return to Point 2.
Checking the straps
With both hands, try to pull the helmet backwards and forwards as far as possible. Make a concerted
effort. This is important. If you can slide the helmet backwards to the point where your forehead is bare or
forwards to the point where your visual field is impaired, then the helmet is not properly adjusted. Repeat
Points 2-6 until helmet movement is at a minimum.
WARNING! In the event that you are unable to fit the helmet in such a way that, with fastened straps,
the helmet can only be moderately moved backwards and forwards, DO NOT USE THIS HELMET!
Replace it with a smaller one or a different model from the CASCO line.
10
B: MAINTENANCE INSTRUCTIONS
Clean your helmet using our special helmet care products (CASCO helmet cleaner, CASCO helmet
refresher) or use water, mild detergent and a soft cloth. The interior lining and mesh of the helmet can be
replaced as required. Do not use any type of solvent. Proper cleaning, care and treatment is a requirement
for trouble-free functioning.
C: HELMET ALTERATIONS
This CASCO helmet was produced in series, tested and released according to the corresponding standard.
Warning: A helmet compliant with the European standard and labelled as such, may not comply with all
areas thereof when worn in conjunction with further items of personal protective equipment or accesso-
ries (other than those accessories specifically intended for use with this helmet by the manufacturer). Due
attention should be paid to the information provided by the manufacturer in this regard.
The CASCO helmet should not be altered in any way or other brand component parts used. The wrong or
substituted interior fittings and other alterations such as subsequently added boreholes for accessories
defeat the safety purpose of this helmet and invalidate the warranty. Only those replacement parts and
accessories intended for use with a given helmet may be used. If in doubt, please contact CASCO Inter-
national GmbH directly.
Further alterations to the helmet, specifically the use of cleaning substances, chemicals and lacquers,
paints and pigments, solvents, adhesives or self-adhesive labels can pose a serious safety risk. Only use
those media, accessories and spare parts which have been approved by CASCO should be used.
D: HELMETS FOR TECHNICAL RESCUE WORK / COMBATING FOREST AND WILDFIRE
Standard colours
PF 100 Rescue white-red .......................................................................................................... 8.100.17
PF 100 Rescue day-glow .......................................................................................................... 8.100.13
Additional colours/special colours on demand
SPARE PARTS AND ACCESSORIES
Only original accessories and original spare parts may be used. Approved accessories are:
Visor shield Hellberg 2 mm PC standard ................................................................................ 8.2047.00
Visor shield Hellberg 2,5 mm PC Anti-fog .............................................................................. 8.2047.01
Visor frame visor Hellberg ....................................................................................................... 8.2047.10
Mesh visor Hellberg
(accepted use only in line with EN 1731)
Visor mount set for Hellberg ................................................................................................... 8.2047.20
Neck guard ................................................................................................................... 8.3028.S / M / L
Winter fittings Nomex .................................................................................................... 8.2050.S / M / L
Flashlight UK 4AA ES1 Xenon ................................................................................................. 8.5035.02
Ear protectors Hellberg .......................................................................................................... 8.2049.00
Visor and lamp mount ............................................................................................................. 8.5038.01
Your helmet comes with exchangeable interior fittings with exchanging pin.
Please release the pin carefully on replacement (Fig. 3).
.................................................................. 8.2048.00
11