Endress+Hauser iTEMP TMT 122 Bedienungsanleitung Seite 30

3 Commissioning
30
OFFSET Entry of zero point correction (Offset).
• V0H5 Entry: -10.00...10.00 °C (°C, °F, K)
0.00 °C
Hint!
Entry returns to factory default values when changing sensor type!
Function group: BASIC CALIBRATION
Type of sensor Entry of sensor used:
• V2H0 Sensor type
-10..75 mV
10..400 Ohm
10..2000 Ohm
Pt100 DIN
Pt100 JIS
Pt500
Pt1000
Ni100
Ni500
Ni1000
Polynom RTD
Type B
Type C
Type D
Type E
Type J
Type K
Type L
Type N
Type R
Type S
Type T
Type U
Polynom TC
Pt100 DIN
Temp.Compensation Selection of temperature compensation of the cold junction when using
• V2H1 customer specific linearisation of the TC polynom
Input:
None, Type B, Type C, Type D, Type E, Type J, Type K, Type L, Type N,
Type R, Type S, Type T, Type U
None
Unit meas. value Enter engineering units.
• V2H2 Entry: °C
°C
Current output Enter standard (4-20 mA) or inverse (20-4 mA) current output signal.
• V2H3 Entry:
4-20 mA
Value for 4 mA Entry: For limits see unit function SENSOR TYPE.
• V2H4 0 °C
Value for 20 mA Entry: For limits see unit function SENSOR TYPE.
• V2H5 100 °C
Range start
-10 mV
10 Ω
10 Ω
-200 °C (-328 °F)
-200 °C (-328 °F)
-200 °C (-328 °F)
-200 °C (-328 °F)
-60 °C (-76 °F)
-60 °C (-76 °F
-60 °C (-76 °F
-270 °C (-454 °F)
0 °C (32 °F)
0 °C (32 °F)
0 °C (32 °F)
-270 °C (-454 °F)
-210 °C (-346 °F)
-270 °C (-454 °F)
-200 °C (-328 °F)
-270 °C (-454 °F)
-50 °C (-58 °F)
-50 °C (-58 °F)
-270 °C (-454 °F)
-200 °C (-328 °F)
-270 °C (-454 °F)
°F
K
4-20 mA
20 - 4 mA
iTEMP® HART® Communication
Range end value
75 mV
400 Ω
2000 Ω
850 °C (1562 °F)
649 °C (482 °F)
250 °C (482 °F)
250 °C (482 °F)
180 °C (356 °F)
150 °C (302 °F)
150 °C (302 °F)
2500 °C (4532 °F)
1820 °C (3308 °F)
2320 °C (4208 °F)
2495 °C (4523 °F)
1000 °C (1832 °F)
1200 °C (2192 °F)
1372 °C (2501 °F)
900 °C (1652 °F)
1300 °C (2372 °F)
1768 °C (3214 °F)
1768 °C (3214 °F)
400 °C (752 °F)
600 °C (1112 °F)
2500 °C (4532 °F)
Endress+Hauser