Grundig EC 7400 RDS Serviceanleitung Seite 27

EC 7400 RDS/EC 7500 RDS Allgemeiner Teil / General Section
Coding
Your personal Code Number is located on the
Identity Card for your car radio.
Coding is not activated when the r
the factory.
Ifyou have "activated" your car radio's
coding:
As soon as you take the car radio out or dis-
connect it from the car battery (or permanent
plus clamp 30), it is electronically blocked.
Only you are abie to put it back into operation
by entering your personal Code Number
(Return to operation, page 1-27).
If th Number is lost (Identity Card),
only a dealer can put the radio back into
operation after you provide proof of owner-
ship and pay a fee.
ts the coding activated?
Radio is playing:
Press (UM_} button until signal sounds.
In display:
> SAFE < Coding activated, or
> CODE < Coding not activated.
Then:
Press (WH_) button until signal sounds.
Activating coding
1. Radio is playing.
2. Press (U#_) button until signal sounds:
> CODE < is in display.
After approx. 3 seconds:
>----<is in display.
If you wish to terminate "Activate coding":
Press ZH] button until signal sounds, or
switch car radio off and on again.
3. Input Code No. (see Identity Card) using
the buttons G0) ZG C2.
OOwe
Repeatedly press buttons...
— briefly: 1, 2, 3, 4...(forwards)
— longer: 0, 9, 8, 7...(backwards)
until Code No. is in display.
4. Confirm Code No.:
Press GEHL) button until signal sounds:
> SAFE <is in display.
After approx. 3 seconds:
Radio plays.
The coding is activated!
Waiting periods
Wait times are required between activation
attempts so that "Return to operation" or
"Deactivate coding"
are not possible by trial and error. During
these waiting periods the car radio input
function is locked for all entries.
During the waiting period
the car radio must be switched on, with
> SAFE < in the display.
The waiting period is over when the number
attempt is visible] (in display) | (approx.)
in the display,
e.g.
>2----<«,
The table shows
the waiting peri-
ods between the
individual
attempts.
Waiting period
after the 7th attempt is always 24 hrs.!
After the 6th attempt we recommend having a
dealer complete the "Return to operation" or
"Deactivate coding" process.
Return to operation
The car radio is electronically blocked after it
has been disconnected from the car battery
(orpermanent plus clamp 30 of your vehicle),
€.g., after it has been removed.
1. Switch on car radio:
> SAFE <is in display.
After approx. 3 seconds:
>| ----<is in display.
2. Enter Code No. (see Identity Card) with the
buttons GI ZI GIG)
MGI
Press buttons repeatedly...
— briefly: 1, 2, 3, 4...(forwards)
~ longer: 0, 9, 8, 7...(backwards)
until Code No. is in display.
3. Confirm Code No.:
Press GLH) button until signal sounds:
> SAFE <is in display.
After approx. 3 seconds:
Radio piays.
> SAFE < remains in display.
Radio does not play.
Begin again.
Be sure to observe the "waiting periods"
between attempts.
Deactivate coding
e.g., before removing the car radio:
1. Radio is playing
Press (Z_} button until signal sounds:
> SAFE <is in display.
After approx. 3 seconds:
>| ----<is in display.
2. Enter Code No. (see Identity Card) with the
buttons ZG) GI @).
OW)
Press buttons repeatedly...
— briefly: 1, 2, 3, 4...(forwards)
~ longer: 0, 9, 8, 7...(backwards)
until Code No. is in display.
3. Confirm Code No.:
Press (Qi) button until
> CODE <is in display.
After approx. 3 seconds:
Radio plays.
The coding is no jonger activated!
jut:
> SAFE < remains in display.
Radio does not play.
Begin again.
Be sure to observe the "waiting periods"
between attempts.
GRUNDIG Service-Technik
1-27