Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
8
Make sure the cap is screwed on tightly, so that no detergent
can get into the container during the wash program (this could
damage the water softener beyond repair).
As soon as this procedure is complete, run a program without
loading. The "Pre-Wash" program alone is NOT SUFFICIENT
Residual saline solution or grains of salt can lead to corrosion,
rreparably damaging the stainless steel components.
The guarantee is not applicable if faults are caused by such
circumstances.
Adjusting the dosage of rinse aid
if you are not completely satisfied with the drying results, you
can adjust the quantity of rinse aid used.
• Switch the dishwasher on using the ON/OFF button
' Switch it off using the ON/OFF button
• Press button Ed three times - a beep will be heard.
• Switch it on using the ON/OFF button.
• The current selection level number and rinse aid indicator
!ight flash
• Press button M to select the level of rinse aid quantity to be
supplied
• Switch it off using the ON/OFF button
Setting is complete!
Only use salt that has been specifically designed for
dishwashers. If the salt container is not filled, the water
softener and the heating element may be damaged
as a result of limescale accumulation. Using of Salt is
recommended with any type of dishwasher detergent.
Whenever you need to add salt, it is mandatory to complete
the procedure before the beginning of the washing cycle to
avoid corrosion.
If the rinse aid level is set to ZERO, no rinse aid will be supplied
The LOW RINSE AID indicator light will not be lit if you run out
of rinse aid. A maximum of 5 levels can be set according to the
dishwasher model. The factory setting is specific to the model,
please follow instruction above to check this for your machine.
• if you see bluish streaks on the dishes, set a low number (1-2).
• if there are drops of water or limescale marks on the dishes.
set a high number (3-4).
Setting the water hardness
To allow the water softener to work in a perfect way. It is
essential that the water hardness setting is based on the actual
water hardness in your house. This information can be obtained
from your local water supplier. The factory sets the default
water hardness
Filling the detergent dispenser
To achieve the best washing and drying results, the combined
useof detergent, rinse aid liquid and refined salt is required. We
recommend using detergents that do not contain phosphates
or chlorine, as these products are harmful to the environment.
Good washing results also depend on the correct amount of
detergent being used
Exceeding the stated amount does not result in a more effective
wash and increases environmental pollution. The amount can
be adjusted to the soil level. In the case of normally soiled items,
use approximately either 25g (powder detergent) or 25ml (liquid
detergent) and additional tea spoon of detergent directly inside
the tub. If tablets are used. one tablet wIll be enough.
If the crockery is onty lightly soiled or if it has been rinsed
with water before being placed in the dishwasher, reduce the
amount of detergent used accordingly (minimum 25 g/ml) e.g.
skip the powder/gel putted inside the tub
Switch on the appliance by pressing the ON/OFF button.
Switch off the appliance by pressing the ON/OFF button.
Hold down button Ev] for 5 seconds, until you hear a beep.
Switch on the appliance by pressing quickly the ON/OFF
button
The current selection level number and the salt indicator light
both flash
Press button Eg to select the desired hardness level (see
WATER HARDNESS TABLE).
Switch off the appliance by pressing the ON/OFF button.
Setting is complete!
Water Hardness Table
'dH
German
degree}
0-6
Soft
Medium
7-11
12-16
Average
3
17 - 34
Hard
4
Very hard
5
35 - 50
;engg;Lses
degrees
11 - 20
21 - 29
30 - 60
61 - 90
To open the detergent
dispenser press button C.
Introduce the detergent
into the dry dispenser D
only.
Place the amount of
detergent for
pre-washing directly
inside the tub.
Filling the rinse aid dispenser
Rinse aid makes dish DRYING easier. The rinse aid dispenser A
should be filled when the RINSE AID REFILL indicator light @ in
the control panel is lit.
1. When measuring out the detergent refer to the mentioned
earlier information to add the proper quantity. Inside the
dispenser a there are indications to help the detergent
dosing
2. Remove detergent residues from the edges of the dispenser
and close the cover until it clicks
3. Close the lid of the detergent dispenser by pulling it up until
the closing device is secured in place,
The detergent dispenser automatically opens up at the right
time according to the program. If all-in-one detergents are used,
we recommend using the TABLET button, because it adjusts the
program so that the best washing and drying results are always
achieved
1. Open the dispenser B by pressing and pulling up the tab on
2. Carefully introduce the rinse aid as far as the maximum (110
mI) reference notch of the filling space - avoid spilling it. If this
happens, clean the spill immediately with a dry cloth.
3. Press the lid down until you hear a click to dose it.
NEVER pour the rinse aid directly into the tub.
the lid
Werbung
