GRE High Line Bedienungsanleitung Seite 35

Stahlwandbecken

Seite von 48

/ 48
Lesezeichen

r.;;.,_____

RESPECT THE ENVIRONMENT

V----- 00 NOT TAKE APART THE POOL UNLESS IT 15 STRICTLY NECESSARY. IF YOU 00 SO, PLEASE REUSE THE WATER.

WATER 15 A SCARCE GOOO.

MAINTENANCE AND USE:

- Switch on the filter system once a day in to insure a complete water volume renewal and never do it when somebody is in the pool (see filter manual).

- Check the filter's level of clogging regularly in summer when the pool kit is in use.

- Check screws, nuts and washers (for rust).

- The pool water level has always to be hold in a minimum of 15 cm from the pool superior edge.

- Never empty the pool completely. Low water levels may cause serious damage to the pool.

- Failure to comply with the maintenance instructions may lead to serious health risks, especially for children.

- The use of a swimming costume entails respect for the safety regulations sei out in the maintenance and user guide.

- Never leave a pool kit empty on the ground, outdoors.

- Clean regularly the P.V.C liner and the water level mark with non-abrasive pnoducts. Regularly clean the fold joining the bottom to the side of the liner, as it is an area where

dir! accumulates. lfyou do by accident a small hole in the liner, you can repair it thanks to our nubber patchesAR202 orV12.

• The isothenmic covers (for the summer) pnotect your pool from insects, dust, leaves, ... and avoid to loose the water temperature. Do always sei it in order the bubbles are in contact

with the water.

WINTER-SEASON:

A) IF YOU CHOOSE NOT TO DISMOUNT THE POOL:

1- Clean the liner bottom and sides with a non-abrasive pnoduct.

2- Treat the water with a chemical product for wintering.

3- Leave the pool full of water considering:

a) For pools with skimmer and refulling pipe, reduce the water level 5 cm underneath the skimmer and close the refulling pipe with the screw tap which is included

with the filter.

b) For pools with exhaustion and refulling pipes, reduce the water level 20 cm fnom the superior edge of the pool and close the pipes using the screw system

incorporated.

4- Disconnect the pipes. Do not dismount the skimmer and the refulling and exhaustion pipes.

5- Protect the pool with a winter cover, and pul a floating element between the cover and the water, in order to protect it from frost.

6- Filter: disconnect it from the pool. Clean it, empty the sand or remove the cartridge, dry it and keep it in a covered and sheltered from dampness place.

7-Accessories: remove every accessories (ladder, alarm, spotlight, pole ... ), rinse them with soft water and tidy them

away.

TO RUN THE POOL AGAIN: Remove the winter cover, install the filter, change at least 1/3 of water and realize a chlorine treatment. Switch on the filter for at least 8

hours in an uninternupted way, respecting the continuous working period indicated in the filter manuals.

B) IF YOU CHOOSE TO DISMOUNT THE POOL:

1- Empty the pool. Measures: Filter, Automatie pump for handling clean water or communicating vessels system. Communicating vessels system: Use the hose from

your filter with the smallest cnoss-section. Fixa weight to one of its end and plunge it into the swimming pool. After this, sink the whole hose, until there is no air inside.

With one hand, and under the water stop up hermetically the end of the hose and take it to the emptying point. Remove hand, and water will start running. Do not use

this water for watering the plants, because il contains chemical products.

2- Clean every pool constituents with a sponge and a soap product with a neutral pH. Dry them and tidy them away in a dry and clean place.

That's normal !hat after having installed and dismounted the pool several times, the P.V.C liner dilate and loose its elasticity.

TO RUN THE POOLAGAIN: Read another time this manual instnuctions from the beginning.

CHIMICAL MEASURES:

Please read carefully the chemical product manufacturer instnuctions. WARNING: Keep chemical products in a clean, dry and out of children place. lmportant: Every products

used have to be compatible with the P.V.C liner.

- First filling: Analyse the water pH and chlorine {Cl) and adjust them to the optimal levels: pH: 7,2 - 7,6; Chlorine: 0.5 - 2 ppm.

• Chlorine treatments: Consist in increasing the chlorine level until approximatively 20 ppm to eliminate germs and seaweeds. This process has to be done only when

the pool water comes fnom rivers or ponds, ... or if it stayed a lang time without any treatments.

- Checking: Check at least once a week the chlorine levels (use a chlorine and pH analyser). In the same way, we advise to add an algicid to prevent seaweeds appearance.

Never have a swim before the chlorine level stabilization. Do always use a floating dispenser for the chemical product (tablets) dissolution. The chemical pnoduct

measuring out has tobe done in accordance with: Your pool water volume, the bathe frequency, the climatic conditions, the water temperature and the location. Do

always move the water and wait for the chemical pnoduct dissolution before adding another one. Wait appnoximatively 12 hours between any pH, chlorine or algicid

adjustment using the filter system.

MECHANICAL MEASURES:

Check the filter, the skimmer, the valves and the pipes are weil connected to the pool. Do consider high water temperature will involved more time for the filtering.

Theoretic filtering time= Waier volume /Filtersystem discharge (generally 8h/day with water temperature of 21°C), (Ideal: 2h in the morning - 4h around midday-

in the afternoon).

PLEASE

RESPECT THE CONTINUOUS WORKING

PERIOD

INDICATED

THE

FILTER MANUALS.

VACUUM CLEANER (MANUAL OR AUTOMATIC):

Only for pools with skimmer. Connect an hose extremity to the brush head and immerse it into the water to make it fill in. Connect the other pipe extremity to the

exhaustion adapter (TA) and place it above the skimmer basket. Switch on the filter in the FILTERposition and begin to clean the bottom. Pay special attention to areas

with folds where dir! accumulates.

BOTTOM CLEANER VENTURY STYLE:

Connect a garden hose to the bollom cleaner join and introduce it into the pool. Open the tap until a normal pressure to make the water flow out against the bollom of

the pool, producing in !hat way an ascendant stream which leave the dir! into the filter (bag) which is adjust on the bottom cleaner.

PROBLEM

CAUSE

SOLUTION

Muddywater

Bad filtralion. High PH. Organic residues in

Realice un contralavado del filtro. Aiiada CLARIFICANTE en pastillas en un dosificador. Realice una

excess

Cloraci6n de choque.

Green water

Seaweed or mud formation

Cepillar suavemente el fondo y las paredes de la piscina. Analice el PH y ajustelo entre 7,2-7,6. Aiiada