Installing The Seat - Lorelli Colombo Gebrauchsanweisung

Vorschau ausblenden

Seite von 48

/ 48
Inhalt
Inhaltsverzeichnis
Lesezeichen

Inhaltsverzeichnis

Verfügbare Sprachen

Strap length adjustment

IELoosening the straps: Press the strap adjustment button "11" (Picture 1) and at the same time pull the

two shoulder straps "4" (Picture 2) Note: Do not pull Onthe shoulder pads.

2. Tightening the straps: Place the child in the seat, fasten both straps in the centre buckle (Picture 3) and

pull the strap at the middle of the seat. (Picture 4)

Fastening the harness.

1. Connect the two metal pieces at the end of the straps (Picture 5) and insert them into the centre buckle

(Picture 6) until you hear a click.

2. Check that the harness is secure by pulling the shoulder straps upwards.

3. To release the harness. press on the red central buckle button. (Picture 8)

Headrest and shoulder strap height adjustment,

The headrest can be adjusted in 9 different positions (Picture 9). Adjusting the height Ofthe shoulder straps

(in 2 positions) is done by moving them to a different position, releasing them from the buckle at the back.

Pull the adjustment handle (12) (Picture 10), move the headrest to the desired position up and down

according to the height of your child. Release the handle and you should hear a click, which is a signal that

the headrest is locked. Please ensure that the headrest is positioned correctly around the child's head.

(Picture 12). The position of the straps should be at the level of or slightly above the child's shoulders.

Make sure the straps fit properly over the child's shoulders. The headrest of the safety seat must be

adjusted to provide a distance of about 2 fingers between the child's shoulder and the lower edge of the

headrest.. (Picture 13)

1. Place the child seat firmly on the car seat facing forward "in the direction Of travel" and use the 3-

point seat belt.

2. Remove the inner seat pads, then lift the head cushion (Picturel 4)

3. Fasten the seat with the car safety belt (Picture 15) by passing the shoulder belt through the two

guides of the headrest and backrest (Picture 16) and pass the lap belt under the harness and armrests

ofthe seat. Place the inner seat pad and headrest cushion (Picture 17).

Fasten the belt into the vehicle buckle until it clicks. (Picture 18) Press the seat to the car seat and

tighten the safety belt by pulling on it (Picture 19) and making sure it is not twisted (Picture 7). Make

sure the seat is installed correctly,

Dismantling

the harness.

1. H Press the red button to release the shoulder straps (Picture 20)

2. Remove the cushion from the headrest and seat pad (Picture 21 )

3. Unhook the shoulder straps from the metal hook (Picture 22)

4. Pull the seat belts out Of the backrest

and the shoulder straps from the buckle. (Picture 23)

5. Slide the metal plate through the opening in the base of the body and pull it out from the top of the

seat. (Picture 24 and 25)

6. Keep all accessories

I—Route of the adult safety belt, forward-facing,

Route the seat belt as shown in (Picture 26 and 27) and fasten until you hear a

"click".

Pull on the

twisted.

2. Route of the adult safety belt, forward-facing,

Route the seat belt as shown in (Picture 28, 29) and fasten until you hear a "click".

Pull on the seat belt to make

Removing

the cover.

I—Removal

- pull up the headrest. Detach the top of the cover. Remove the cushion,

shoulder pads and the straps (Picture 30 and 31). Separate the seat pad. The main cover of

the chair is removed and pulled out. (Picture 32)

2. Replacing the cover: To replace the cover, please repeat the steps above in reverse order.