Atlas Copco QMC41-100-I06 Sicherheitshinweise Seite 6

Safety Information
• Only use the cord supplied with the controller to connect
to the mains, and the cord supplied with the tool to con-
nect to the controller. Do not modify the cords or use
them for other purposes. Use only genuine replacement
parts. Failure to follow these instructions may result in
electric shock.
Entanglement hazards
• Keep away from rotating drive. Choking, scalping and /
or lacerations can occur if loose clothing, gloves, jew-
ellery, neck ware and hair are not kept away from tool
and accessories.
• Check that all guards are securely in place before each
operation of the tool.
• Gloves can become entangled with the rotating drive,
causing severed or broken fingers.
• Rotating drive sockets and drive extensions can easily
entangle rubber-coated or metal-reinforced gloves.
• Do not wear loose-fitting gloves or gloves with cut or
frayed fingers.
• Never hold the drive, socket or drive extension.
Projectile hazards
• Always wear impact-resistant eye and face protection
when involved with or near the operation, repair or
maintenance of the tool or changing accessories on the
tool.
• Be sure all others in the area are wearing impact-resis-
tant eye and face protection. Even small projectiles can
injure eyes and cause blindness.
• Serious injury can result from over-torqued or under-
torqued fasteners, which can break, or loosen and sepa-
rate. Released assemblies can become projectiles. As-
semblies requiring a specific torque must be checked us-
ing a torque meter.
NOTE So-called "click" torque wrenches do not check
for potentially dangerous over-torqued conditions.
• Do not use hand sockets. Use only power or impact
sockets in good condition.
• Ensure that the workpiece is securely fixed.
Operating hazards
• Operators and maintenance personnel must be physically
able to handle the bulk, weight and power of hand-
guided fixtured tools. Be ready to counteract normal or
sudden movements, use both hands.
• Guard against electric shock. Avoid body contact with
earthed or grounded surfaces (e.g. pipes, radiators, other
electrical machinery). There is an increased risk of elec-
tric shock if your body is grounded.
• Immediately after performing adjustments or programme
changes, check for correct operation.
• When working with hand-guided fixtured tools, maintain
a balanced body position and secure footing.
Workplace hazards
• Slip/Trip/Fall is a major cause of serious injury or death.
Cluttered areas and benches invite injuries.
6 © Atlas Copco Industrial Technique AB - 9834 3502 00
• Daily check hooks, shackles, chains and mounting points
used for suspending fixtured tools. Do not use if cracked,
worn or damaged.
• Do not expose electric power tools to rain. Do not use in
damp or wet conditions. Water entering a power tool will
increase the risk of electric shock.
• High sound levels can cause permanent hearing loss and
other problems such as tinnitus. Use hearing protection
as recommended by your employer or occupational
health and safety regulations.
• Repetitive work motions, awkward positions and expo-
sure to vibration can be harmful to hands and arms. If
numbness, tingling, pain or whitening of the skin occurs,
stop using tool and consult a physician.
• Proceed with care in unfamiliar surroundings. Be aware
of potential hazards created by your work activity. This
tool is not insulated from coming into contact with elec-
tric power sources.
• This tool and its supply unit are not recommended for
use in potentially explosive atmospheres.
DO NOT DISCARD – GIVE TO USER
Useful Information
Website
Information concerning our Products, Accessories, Spare
Parts and Published Matters can be found on the Atlas Copco
website.
Please visit: www.atlascopco.com.
ServAid
ServAid is a portal that is continuously updated and contains
Technical Information, such as:
• Regulatory and Safety Information
• Technical Data
• Installation, Operation and Service Instructions
• Spare Parts Lists
• Accessories
• Dimensional Drawings
Please visit: .
For further Technical Information, please contact your local
Atlas Copco representative.
Caractéristiques techniques
Conditions environnementales normales
Ce produit est conçu pour fonctionner en toute sécurité dans
les conditions suivantes :
• Utilisation à l'intérieur
• Jusqu'à 2000 m au-dessus du niveau de la mer
• Température de fonctionnement de +5 °C / +41 °F à +40
°C / +104 °F
QMC41-100-I06