Ruris RXR800 Bedienungsanleitung Seite 39

EN
9. Repeat steps 5-8 to select the working hours for each day of the week.
10.Press the OK button (7) to confirm the setting.
Deleting a lawn mowing program
1. Move the selection with the arrow buttons (6) to "Alle" (upper left).
2. Press and hold the back button (5) to delete the entire schedule for the week.
Establishing secondary areas
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN (factory setting "1111).
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Secondary areas".
5. Press the OK button to select a secondary zone (Area). Select the starting distance "Distance (dst)m"" and
the ratio "Percent (pct)%" of the area to be mowed using the arrow buttons (6), then press the OK button to
confirm.
6. Repeat step 5 to complete the set of each subzone (Zones).
7. Press the OK button (7) to confirm the settings.
The robot travels the distance "Distance (dst)m" specified by you, along the boundary wire (1 - 500 meters)
and then starts working. )
By entering the percentage "Percent (pct)%" you specify what percentage of the total area inside the boundary
wire is to be trimmed.
The sum of the "Percent (pct)%" of the 5 secondary areas (Areas) must be less than or equal to 100
Returning to factory settings
The robot can be reset, returning it to factory settings
1. If necessary, open the cover (1).
2. Unlock the display (10) with the 4-digit PIN (factory setting "1111").
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Setting".
5. Confirm the selection with the OK button (7).
6. Use the arrow buttons (6) to select "Factory set".
7. Confirm the selection with the OK button (7).
The robot shuts down and returns to factory settings. The reset will not delete the settings and data saved in
the Tuya Smart App.
Cutting height adjustment
The robot has cutting height adjustment settings between 25mm and 60mm. If the grass is larger than 60 mm,
cut the grass to max. 60 mm, otherwise the work load of the robot will be too high and the cutting efficiency will
decrease. Use a regular lawnmower. Once the installation is complete, the cutting height can be adjusted to the
appropriate height. Always start in a high cutting position and work your way down to the desired height.
Note: Do not attempt to raise or lower the cutting height while the robot is mowing the lawn.
Connecting the robot with TuyaSmartApp (for RXR1000 model).
1. Open the cover (1).
2. Unlock the display (10) with the 4-digit PIN (factory setting "1111).
3. Press the OK button (7) to enter the main menu.
4. Use the arrow buttons (6) to select "Settings".
5. Confirm the selection with the OK button (7).
6. Use the arrow buttons (6) to select "Set WiFi".
7. Activate Bluetooth® on your smartphone.
8 . Open the Tuya Smart app. From here there are 3 options to connect the device.
If this is the device you want to connect to the app:
9. Select the "Add Device" option. The application scans the area to find available devices.
10.If you select "Got to add", they are displayed in a list.
11.Select a single device.
12.Now tap on , select the device.
13.Select your WLAN and enter the appropriate password.
14.Confirm the connection by pressing "Finish".
The device is now listed
If you have already connected other devices to the app :
9. In the setting , select
devices have been found.
10. Continue as from point 10.
15
and can be selected.
from the top right. The app scans the area for available devices and indicates if
.
, ,