Werbung
BITTEBEACHTENSIEDIEWARNHINWEISE
Bild1giltnurfür 120V Maschinen
(Version USA)
2.
Netzkabelmontieren(Bild2)
Ill
a. Maschinenstecker des Netzkabels von untenher
indasSteckergehäuse
einschieben.
b. SteckermitzweiSchraubensichern.
Ca. 500mmvom Netzkabelende enffernteine
1
Schlaufe bilden.
Die Schlaufe durch den Schlitz der
Kabelzugentlastung
einhängen.(Abb.3)
Sprayschlauch
3.
(Abb.4).
2
3
4
VEUILLEZOBSERVERLES AVERTISSEMENTS
Lamachine 120V estexpédiée d ansuncarton en4
parties s éparées; timon, m oteur/agrégat,
vaporisateur, cåble éiectrique.
Montagedu timon
Placerd'abordles vis dansla fixationdu timon
amFührungsgriff
(v.ill.1).Placer l etimonsurlapartiemoteur.
Ensuite serrerlesboulons et lesécrous depuis
dessous avecuneclefappropriée.
Montage ducåbledalimentation ( ill.2).
Brancherdebas en hautle fiche måle
l'extrémitéducåblecöté machinesuria prise
führenundamHaken
femelle montée danslespoignées d elamachine.
Assurerla ficheau moyendes2 vis.
über N ippel amVentil schieben
Faireuneboucleå env.500 mmde l'extrémité
du cåble.
Passercette boucleau traversde lafentedu
crochetde maintiendu cåbleet l'accrocherå ce
demier.(v.ill. 3)
Relier l etuyau duvaporisateur auraccord d ela
3.
valve(v. ill.4).
TASKI RANGER SUPERSONIC
INSTRUCTIONS
INTRODUCTION
The TASKI r anger supersonic isa508mm (20 ultra
high speed (1200 rpm) buffing m achine forstraight
lineoperation. Ithasa built-in s pray cleaning d evice
andissuitable fordrybumishing, buffingandspray
cleaning o nallhard surface d ecorative floors.
Tocontain andminimise thespread of dustgenerated
bythedeaning action, anoptional suction s kirtand
vacuumunit maybe fitted.
Thefloating pad drivesystem ispermanently attached
ard is arranged t o provide constant p ressure, evenon
anirregular f loor.
ASSEMBLY
Insomeinstances t hemachine issupplied ina
partially dismantled
state, allmain items ( base, handle
& mainscord)beingpacked in a single carton.
To Assemble:
1.
Fit handle(fig.1)
Note:The electriccablebetweenthe handleand
baseunitisalready connected. Takecarenotto
strainthiscablewhilst f ittinghandle.
a. Fit4 screws (M8 X 40)intoholesinhandle
bracketand locatescrewsintocorresponding
holes in machine base.
b. Fitwashersandnutsto screwsfrom underneath.
Tighten withappropriate s panner.
2.. Fit mainscord.(fig.2)
a. Locatemachineconnectorof cordbeneath
connector housing at rearof handle. P ush
connector upwards to locate inreceptacle.
b. Secure coverin position with2 screws.
Form aloop inmains cordapproximately
500mm
from handle connector.
Push loop through slotinstrain relief c leat a nd
engage loopin hook.
Pullcordtight.(fig.3)
Connect solution feedpipe(fig.4)
3.
Pushfreeendof solution feedpipeontohosetail
at bottom of solution control valve.
3
Werbung
