Tunturi R 505 Betriebsanleitung Seite 8

METER/MESSCOMPUTER/UNITE DE COMPTEURS
PANNELLO ELETTRONICO/MATARE/MITTARI
1) DISPLAYS:
- TIME: counts time elapsed from
zero up or preset time down to
zero
- STROKES: counts strokes rowed
up from zero or preset number of
strokes down to zero
- CAUMIN: shows calories con¬
sumed per minute (see CALORIE
DISPLAY)
- CALORIES: shows total calorie
consumption (max 9999 cal)
- SPEED: shows bar diagram display
of rowing speed (max. 60 strokes/
min)
NB. The sticker on the frame on the
right-hand side of the meter shows
the most usual rowing speed ranges -
ordinary exercisers 20-25 strokes/
min, active exercisers 25-35 strokes/
min - and instructs you how to keep
in condition: row 3 times a week, at
least 15-20 minutes at a time.
2) CALORIE DISPLAY (see dia¬
gram I)
In theory, calorie consumption is af¬
fected only by resistance and length of
stroke. As capacity to produce en¬
ergy, or performance, varies in differ¬
ent people, the calorie display can
only give a rough estimate of calorie
consumption.
In the R 505, the LOAD mode gives
calorie consumption for a rower of a
certain height. The recommended
LOAD values given below are based
on the average energy consumption
of test subjects of different heights at
different load levels (see position of
the load adjustment knob).
Example: A 175 cm tall person is re¬
commended to row at the following
LOAD settings at different load
levels:
base load 2.4
I 3.1
II 3.9
III 4.5
llll 5.0
3) AUDIBLE SIGNALS
- signal synchronizing with preset
tempo, e.g.:
setting 2 = 30 strokes/min
setting 3 = 20 strokes/min
setting 4=15 strokes/min
- signal lasting a few seconds on
completion of a preset rowing time
or number of strokes
4) KEYS
ON/QFF: Switches power on/off.
- when power is on, all displays re¬
main on the screen for 3 sec and an
audible signal is given
- all settings except LOAD are at
zero
START/STOP: Switches from START
to STOP mode (when the START
mode is on, the STOP signal goes off
the screen)
- when in the START mode, time,
strokes and calorie consumption
can be counted
- STOP mode interrupts counting;
the values are stored in the mem¬
ory until the RESET key is pressed
MODE: Alternates modes and dis¬
plays.
- N.B. LOAD and TEMPO cannot be
useci when in the START mode (for
these displays switch to STOP)
- for SCAN or automatic alter¬
nation of displays at 5 sec in¬
tervals: when in START mode,
press MODE key for 2 sec
(SCAN signal appears on screen)
SET: Presets required values (when in
STOP mode)
- pressing SET key continuously runs
numbers forward fast
RESET: Returns numbers on display
to zero.
- pressing RESET automatically
switches to STOP mode
- pressing continuously for 2 sec re¬
turns all modes to zero (except
LOAD)
5) SETTINGS:
- time 0:00 - 99:00 (in steps of I
min)
- strokes 0 - 9990 (in steps of 10
strokes)
- tempo 0.000 - 9.875 (in steps of
0.125)
- load 1.0 - 6.6 (in steps of 0.1),
see CALORIE DISPLAY
6) HOW TO SET; e g. strokes
1. switch on power by pressing ON/
OFF key
2. press MODE key until arrow
points to STROKES display
3. preset desired number of strokes
by pressing SET key (STROKE SET
sign (((• appears on screen)
4. start countdown by pressing
START/STOP key (remaining
number of strokes displayed)
I) ANZEIGE:
- TIME: abgelaufene Trainingszeit
oder Countdown
- STROKES: durchgefuhrte Zuge
oder Countdown der vorprogram-
mierten Zugzahl
- CAL/MIN: Kalorienverbrauch/min
s. auch Kalorienanzeige)
- CALORIES: verbrauchte Kalorien
(max. 9999 cal)
- SPEED: semigraphische Darstel-
lung der Rudergeschwindigkeit
(max. 60 Zuge/min)
Trainingshilfe: Der Aufkleber rechts
vom Messcomputer gibt die gangig-
sten Geschwindigkeitsbereiche (fur
den Breitensportler 20-25 Zuge/min
und fur den Ruderwettkampfer 25-
35 Zuge/min) sowie einen Hinweis
iiber die Trainingsfrequenz und
-dauer: Zur Aufrechterhaltung der
Kondition sollte man wochentlich 3
mal mindestens 15-20 min auf einmal
rudern.
2) KALORIENANZEIGE:
Zwar hangt der Kalorienverbrauch
des Trainierenden im Prinzip lediglich
von Rudergeschwindigkeit und Zu-
glange ab, doch die Fahigkeit Energie
zu produzieren eine ganz individuelle
Sache ist, kann die Anzeige der ver-
brauchten Kalorien stets nur ein
Richtwert sein. Durch Verwendung
der LOAD-Funktion (Belastung) wird
der Kalorienverbrauch eines Trainie¬
renden von bestimmter Korpergros-
se berechnet. Der einzustellende
LOAD-Faktor beruht auf Erfahrungs-
werten mit Testpersonen unter je-
weiliger Belastung (vgl. Drehknopf-
stellung).
Bei einer Korpergrosse von 1,75 m
wird unter jeweiliger Drehknopfstel-
lung eine Einstellung des LOAD-Fak-
tors auf folgende Werte empfohlen:
8