Removing The Maxi-Cosi Mobi (Xp); Placing And Securing Your Child; Use Of The Harness System: Closing And Tightening The Harness; Seat Positions (Adjusting The Seat Into Sitting And Reclining Positions) - Maxi-Cosi Mobi Bedienungsanleitung

Checklist ...
To ensure the optimum safety of your child, check after installation to make sure that...
• The seat belts are as tight as possible and not twisted.
• If the car kit is used, it is attached properly and not twisted.
• The tethers are not twisted, are properly secured, and as tight as possible.
• If the Maxi-Cosi Mobi (XP) is installed on the back seat, the support leg is folded out as far as possible,
locked and supported against the floor of the car.
• The entire Maxi-Cosi Mobi (XP) is installed securely and firmly in the car (check by pulling on the seat).

2.2 Removing the Maxi-Cosi Mobi (XP)

• Restore the support leg to its start position by pressing the control button and moving the support leg
38
upwards (38).
• Push the support leg into its folded-up position against the plastic base (39).
39
• Secure the support leg by closing the Velcro strips (40).
40
• Loosen the tethers by pushing the silver button (41,1), pushing the part with the silver button upward
41
(41,2) and pulling on the belt with the hook attached (41,3) (keep silver button pushed in).
TIP: First push the car seat down to lighten the tension of the tethers.
• Release the tether-hooks from the anchor points. (Possibly roll them up and bind them together with an
elastic band.)
• Loosen the car seat belt and remove it from between the plastic base and steel frame (42).
42
• IMPORTANT! If the Maxi-Cosi Mobi (XP) is installed on the back seat, hold onto it while uninstalling to make
sure it does not tip over.
• Remove the Maxi-Cosi Mobi (XP) from the car.

3. PLACING AND SECURING YOUR CHILD

3.1 Use of the harness system: closing and tightening the harness

Once the shoulder belts are adjusted to the proper height as described in section 2.1, Step 1 and your child
has been placed in the seat, you can now secure your child in the seat.
• Slide the buckle sections together and "click" them into the belt buckle (43).
43
• IMPORTANT! Position the lap belt part of the harness system as low as possible in order to safely support
44
your child's hips (44).
• Pull the shoulder belts tight (45,1) and remove any remaining slack from the harness system by pulling the
45
belts tightly using the adjuster belt (45,2).
• IMPORTANT! Make sure you can fit only one finger between the harnesses and your child (46). The tighter
46
the belts are around your child, the better the protection.
• IMPORTANT! Make sure the belt pads are positioned properly against your child's shoulders.
• IMPORTANT! Make sure the belts are not twisted.
• If you are unable to click the buckle sections into the buckle, release the buckle by pressing the red button
and try again.
If you are unable to fasten the harness belts properly or pull them tight, contact your supplier immediately
and do not use the Maxi-Cosi Mobi (XP) under any circumstances.
Always use the belt pads, as they are essential to your child's safety.
Instruct your child to never play with the belt buckle.

3.2 Seat positions (adjusting the seat into sitting and reclining positions)

The Maxi-Cosi Mobi (XP) can be adjusted to 4 different positions (47).
47
• Pull the positioning handle under the front of the seat upwards, and then pull or push the seat forwards or
48
backwards (48).
• Release the positioning handle in the desired position and push until you hear a "click".
Instructions for use
EN
13