Maxi-Cosi Mobi Bedienungsanleitung Seite 6

• Place the Maxi-Cosi Mobi (XP) in the sleeping position (see section 3.2: Seat positions)
• IMPORTANT! Make sure the support leg is in the folded-out position to enable you to access the back of
the Maxi-Cosi Mobi (XP) (see Step 5; Positioning the support leg).
• Pull the shoulder belts until the belt yoke on the back appears and remove the shoulder belts from the belt
5
yoke (5).
• IMPORTANT! Make sure the belt buckle is locked in order to prevent the belts from twisting.
• Pull the shoulder belts out of the belt pads through the shell and cover. Do this on both sides (6).
6
• TIP! Loosen the top part of the cover to make it easier to remove the belts and belt pads. Remember to
EN 7
reattach the cover to the shell afterwards (7).
• Remove the belt pads (8).
8
• From the front, thread one belt pad through the correct slot in the cover and shell and then rethread this
9
belt pad through the back through the adjacent slot (9).
• IMPORTANT! Make sure the strap between the belt pads lies tight against the plastic shell and does not
Mobi
become entangled with the belt portion of the support leg.
Semibold Italic 36 pt
Mobi XP
• Thread the shoulder belts through the adjusted belt pads, cover and shell (10).
10
• Attach the shoulder belts to the belt yoke and check to make sure the 3 red stitching on the belt ends and
11
the belt yoke are facing the shell (11) (if not, this means the belts are twisted).
Mobi
• IMPORTANT! Make sure the belts are threaded along the plastic shell, remain behind the rods and do not
12
Semibold Italic 36 pt
Mobi XP
become entangled with and stay behind the belt portion of the support leg (12).
Mobi
Adjusting the height of the shoulder belts
Semibold 36 pt
Mobi XP
The correct belt height of the shoulder belts is attained when the belt disappears into the shell slightly above
XP1
theshoulder of the child. Make sure that the shoulder belts fit properly over the shoulders of the child (XP1).
• Loosen the shoulder belts by pressing the release button and pulling the shoulder belts towards you as far
01
aspossible (01) Important: Do not pull the belt pads when doing so.
• Lift up the flap on the cover by the shoulder belt slots (XP2).
XP2
• To make the adjustment easier, pull the shoulder belts on top of the belt pad forward into a loop, loosening
XP3
them (XP3).
• Next, push the loop back through the opening (XP4).
XP4
• Slide the shoulder belt and the belt pad strap through the slot together into the next position (XP5). Make
XP5
sure that theshoulder belt is positioned on top of the belt pad strap in the new position (XP6). Always do
XP6
this on both sides.
• Pull the shoulder belts tight by pulling on the belts under the belt pads (XP6).
XP6
• Place the flap back in position and thread the belt pads through the correct slots in the flap and secure
XP7
them with theVelcro (XP7).
• Check whether you are able to use the belts and ensure they are not twisted.
Step 2: Checking for anchor points or installing the car kit
Remove the elastic band from around the tethers and let the tethers drop to the floor. There are three ways to
hook the tethers onto the anchor points in the car. Specific anchor points may already be present in the car that
can be used. If not, the car kit components or metal attachment hooks provided can serve as anchor points.
Whenever possible, use the most forward positioned anchor points to attach the tethers.
Anchor points already present in the car
• Check the passenger seat rails for anchor points.
In some cars, the child seat anchor points are part of the rail itself (13). In others, there are metal child
13 14
seat anchor loops bolted to the rail, often painted blue (14).
• Check whether the hooks of the tether can be easily connected to and disconnected from the present
anchor points (15). If so, use these points to anchor the Maxi-Cosi Mobi (XP).
15
• IMPORTANT! Make sure the straps of the tethers are not twisted.
• Wait with tightening the tethers until after Step 4; Positioning the support leg.
• Wherever possible, use the most forwarded positioned attachment points for the tethers.
Extra anchor points provided with the Maxi-Cosi Mobi (XP)
10
English