Maxi-Cosi Mobi Bedienungsanleitung Seite 8

Step 3: Installation of the Maxi-Cosi Mobi (XP)
• IMPORTANT! On some seats, the belts are fitted so far forward that proper installation is not possible. If
this is the case, try another seat.
• IMPORTANT! In some cases, the buckle of the car belt may be too long and therefore sit too high against
the base of the Maxi-Cosi Mobi (XP). If this is the case, the Maxi-Cosi Mobi (XP) cannot be installed
securely and
you'll have to choose another position in the car. If you have any questions, please contact the manufacturer.
• Place the Maxi-Cosi Mobi (XP) on the seat and, using the dashboard supports, lean it against the:
EN
a) Dashboard, if installed on the front seat (20).
20
b) Front seat(s) if installed on the left/right (21) and middle (22) of the back seat.
21 22
• IMPORTANT! Place the Maxi-Cosi Mobi (XP) as far as possible with the front to the back of the seat (23) and
23 24
make sure the marking on the plastic base is aligned with the end of the seat of the car (24). If necessary,
25
slide the passenger seat forward or backward until the marking is aligned with the end of the seat (25).
• Place the Maxi-Cosi Mobi (XP) in the sitting position (see section 4.2: Seat positions).
• Attach the tethers; Do not tighten until after Step 4; Positioning the support leg (17/19).
17 19
Step 4: Positioning the support leg
• IMPORTANT! When installing on the back seat, always use the support leg to ensure the safe use of the
Maxi-Cosi Mobi (XP). The support leg does not need to be used when installing on the passenger seat
(leaning against the dashboard).
• IMPORTANT! If the Maxi-Cosi Mobi (XP) is installed on the back seat, slide the passenger seat forward in
26
order to create enough space for the support leg of the Maxi-Cosi Mobi (XP) (26).
• Fold out the support leg by opening the Velcro strips (27).
27
• IMPORTANT! Make sure the support leg is folded out as far as possible. The belt portion of the support leg
28
should now be tight (28).
• Hold onto the support leg under the control button and press the control button with your thumb (29).
29
• Keep the button pressed and move the support leg downwards until it reaches the floor of the car.
• Release the control button and "click" the support leg into the locked position (30).
30
• Check to make sure the support leg is securely locked and stays in position by trying to move it up or down
without pressing the control button.
• Slide the passenger seat backwards again to create enough room for the legs of the passenger on the front
31
seat (31).
Step 5: Tightening the tethers
• IMPORTANT! Slide the passenger seat to the front to make it possible to tighten the tethers (26).
26
• Pull the tethers as tightly as possible first on the side most far from the door by pulling the tether with the
32
loop downwards as hard as you can (32). Then tighten the other s ide (32,2) and give extra tightness by
strapping it down with your foot (32,3).
• Check to make sure the Maxi-Cosi Mobi (XP) is securely and firmly installed in the car by pulling on the seat.
Step 6: Safety belt installation
• The Maxi-Cosi Mobi (XP) can be installed with a dynamic 3-point or a static 2-point safety belt:
a) If you're installing the Maxi-Cosi Mobi (XP) with a dynamic 3-point safety belt, hold the lap and shoulder
33 34
belt (33), thread them between the steel frame and the plastic base (34) and click the seat belt into the car
35
seat buckle (35). Also see the blue markings for proper belt routing.
b) If you're installing the Maxi-Cosi Mobi (XP) with a static 2-point safety belt, hold the lap belt (33), thread it
33 34
between the steel frame and the plastic base (34) and click the seat belt into the car seat buckle (36). Also
36
see the blue markings for proper belt routing.
• IMPORTANT! Make sure the seat belts are not twisted.
• Using the shoulder belt, pull everything to the front of the Maxi-Cosi Mobi (XP) as tightly as possible (37).
37
Make sure the arrow continues to be aligned with the end of the car seat.
12
English