STIEBEL ELTRON LWZ 130 Bedienung Und Installation Seite 58

INSTALLATION
Settings
12.1.4 "Settings" menu
Settings
View
C]' General
C]C]• Language
C]O• Contrast
C]C]• Brightness
C]CJ• Touchsensitivity
CICI• Touch boost
C]C]• Prog. unit software
Air flow rate
C]C]• Flowrate.stageO
CIC]• Flow rate, stage I
Flow rate, stage 2
C]C]• Flow rate. stage 3
C]a• Supply air flow rate offset
Favourites
C]' Humidity prot.
C]CJ• Enable humidity control
C]C]• Humidity prot. interval
C]C]• Humidity threshold
C]Cj• Humidity capture delav
C]• Intensive ventilation
C]Lj• Intens. vent. time
C]• Heat recovery bypass
Setroomtemperature
C]Cj• Operating mode heat recovery bypass
C]C]• Temperature to enable heat recovery
bypass
C]CJZ Temperatureto block heat recovery
bypass
CID' Hysteresisfor heat recovery bypass
C]C]• Temp. differential for heat recovery
bypass
C]a• Window contact mode (A2)
(depending on unit)
C]CJ• Cooling/heating. heat recovery bypass
Frost protection
C]CJ• Frost protection temperature
C]C]• Vernp. t o enable frost protection (A2)
C]CJ• Enable preheating
58 | LWZ 130 | I-WZ 130 Enthalpie
Value
Code for qualified contractor
Day
Hour:Minute
Deutsch
English
Francms
Nederlands
Italiano
Pols I
Cesky
Magvar
Slovensko
S ovens
1 - 10
1 - 10
rnj/h
m3/h
rn3/h
rn3/h
rn3/h
Bypass status
Filter runtime
Device software version
Deviceso tware patch
Mobile device serial no.
Onlyfor qualified contractors
Off
On
h
min
min
Disabled
Bypass/window contact
Outdoorair routingautomatic
Extract air routing autom.
Without window contact
With window contact
Cooling/heating
Cooling
Heating
Onlyfor qualified contractors
Off
On
I LWZ 130 E-W
Condensateprevention (A2)
C]O• Enable condensate prevention
CJCj• Offset condensateprevention
DE Enable fan
Ventilation unit
CJCJ• Device software version
C]Cj• Devicesoftware patch
C]C]• Mobile device serial no.
OO• Devicetype
Settings
C] View
Effect
Standard (AO) The only parameters displayed are those that have been re-
leased for the appliance user and can therefore be accessed
without a code.
Service (A1) Parametersfor qualified contractors: Code"I OOC"
Expert (A2) Parametersfor service department.
To accessactual values and parameters which are reserved
for qualified contractors, enter the code "1 0 0 0" for "View".
Press "0K".
"Service" is shown on the display, when this is entered correctly.
If you switch to the actual values or parameters, you see the en-
abled parameters.
• Notice
After entering the code, switch to the menu by pressing
the "MENU"button. If you first switch to the home screen,
the parameter block is reactivated.
D • Air flow rate
Supply air flow rate offset
Usethis parameter to adjust the supply air flow rate during com-
missioning. The offset refers to standard ventilation and is con-
verted internally as a percentage for the other fan stages.
Example
Nominal flow rate (stage 2)
Offset
Stage Set flow Off- Set flow
rate set rate +
offset
50
1 130
= 225 225/180
2 180 45 180+45
3 235
Off
on
Off
On
rn3/h
rn3/h
Offset fac- internal set flow
rate = set flow
tor
rate * offset factor
50*1.25 = 62
130*1.25 = 162
= 1.25 180*1.25 = 225
235*1.25
= 294
www.stiebel-eltron.com
180
45