Werbung
Verfügbare Sprachen
Verfügbare Sprachen
EnGLIsh
Worklight (Fig. A)
CAUTION: Do not stare into worklight. Serious eye
injury could result.
There is a worklight
7
located on the front of the tool. The
worklight is activated when the trigger switch is depressed, and
will automatically turn off 20 seconds after the trigger switch is
released. If the trigger switch remains depressed, the worklight
will remain on.
nOTE: The worklight is for lighting the immediate work surface
and is not intended to be used as a flashlight.
Operation Modes (Fig. G)
WARNING: Do not select the operating mode when the
tool is running.
CAUTION: Never use in Rotary Drilling or Rotary
Hammering mode with a chisel bit in the bit holder.
Personal injury and damage to the the tool may result.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
symbol
Mode
Rotary Drilling
Rotary hammering
To select an operating mode:
1. Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOTE: The arrow on the mode selector dial
at a mode symbol at all times. There are no operable positions
in between. It may be necessary to briefly run the motor after
having changed from 'hammering only' to 'rotary' modes in
order to align the gears.
Performing an Application (Fig. A, G)
WARNING: TO REDUCE THE RISK OF PERSONAL
INJURY, ALWAYS ensure workpiece is anchored or
clamped firmly. If drilling thin material, use a wood
"back-up" block to prevent damage to the material.
WARNING: Always wait until the motor has come to
a complete standstill before changing the direction
of rotation.
1. Choose and install the appropriate chuck, adapter, and/or
bit onto to the tool. Refer to Bit and Bit Holder.
2. Using the mode selector dial
appropriate to desired application. Refer to
Operation Modes.
3. Adjust the side handle
4. Select the direction of rotation using the forward/reverse
button
. When changing the position of the control
4
button, be sure the trigger is released.
36
to select the
5
application
Screwdriving
Drilling into steel, wood
and plastics
Drilling into concrete
and masonry
5
must be pointing
5
, select the mode
1
as necessary.
-
To select forward rotation, press the for ward/re verse
control button on the right side of the tool.
-
To select reverse, press the forward/reverse control
button on the left side of the tool.
nOTE: The center position of the control button locks
the tool in the off position.
5. Place the bit/chisel on the desired location.
6. Depress the trigger switch
the trigger switch, the faster the tool will operate. For
maximum tool life, use variable speed only for starting holes
or fasteners.
7. To stop the hammer, release the switch.
Recommendations for Tool Operation
•
Large (8 mm to 13 mm) holes in steel can be made easier if
a pilot hole (4 mm to 5 mm) is drilled first.
•
When drilling, always apply pressure in a straight line with
the bit, but do not push hard enough to stall the motor or
deflect the bit. A smooth even flow of material indicates the
proper drilling rate.
•
If drilling thin material or material that is prone to splinter,
use a wood "back‑up" block to prevent damage to
the work piece.
WARNING:
•
Do not use this tool to mix or pump easily combustible
or explosive fluids (benzine, alcohol, etc.).
•
Do not mix or stir inflammable liquids
labelled accordingly.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regular cleaning.
WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are not serviceable.
C
Lubrication
Your power tool requires no additional lubrication.
D
Cleaning
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
3
. The farther you depress
Werbung
