Salewa DYNEEMA HOT G3 Bedienungsanleitung Seite 5

[EN]
A GENERAL
Please read these instructions thoroughly before using this product and follow all the information contained within.
Failure to observe these instructions can lead to a reduction in the protection this product provides.
Please note: mountaineering and climbing are dangerous sports which may lead to unforeseable risks. You are
personally responsible for every action and decision you take. You should acquaint yourself with the related risks
before undertaking these activities. SALEWA recommends that you seek proper training from professionals (such as
mountain guides or climbing schools) before any mountain-related activity. It is important to become familiar with
rescue operations and how they are carried out safely and correctly. The manufacturer declines any responsibility in
case of improper or wrong use. Make sure all the components in your protection equipment are certified.
This product is made in conformity with PPE regulation (EU) 2016/425.
You can view the EU Declaration of Conformity under www.salewa.com.
The product meets the third category for personal protective equipment (PSA).
B INSTRUCTIONS FOR USE
Only use the product for the purpose for which it was constructed and never burden it beyond its limits.
: Danger to life
: Risk of injury
: Correct use
This product protects against the risk of falling during climbing and mountaineering.
The correct use is shown in diagram B.
WARNING: We have not shown all possible misuses.
"Class B" carabiners have been developed for the use in sport and alpine climbing. Every Salewa carabiner has been
individually tested and it complies to EN 12275:2013 Norm.
Always make sure that the carabiner is properly connected to the belay system and that any external bodies, such
as small stones, do not hinder its correct closing.
The Salewa quickdraw slings comply to EN 566:2017 Norm and have been conceived as part of a quickdraw for
climbing.
Always make sure that the top carabiner of a quickdraw can move freely, while the bottom one will be kept in position
by an anti-turn device.
Properly place quickdraws, following the line of the route. The same applies for the subsequent placing of the rope.
C SAFETY INSTRUCTIONS
Before use, carefully check each product part. Diagram C
You should bear in mind that a carabiner may open during use, because of unfavourable friction or while hitting the
rock. Choose belay points where this may be avoided.
Loose fibres on the sling are a clear sign that the product must be retired.
The instructions for use supplied with the product are always to be stored with the product. This product is only to
be used by appropriately trained and/or competent persons, or when the user is under the direct supervision of such
a qualified person.
Make sure compatible and certified parts are used. We recommend the sole use of mountaineering equipment which
complies to the relevant Norms, e.g. EN 892 for ropes, EN 566 for quickdraw slings and EN 12275 for carabiners.
WARNING
·If there is the least doubt about the safety of the product, it is to be replaced immediately.
·A product which has been subject to a fall impact force is not to be used again.
·Any change to this product can reduce safety significantly.
Attention: Dyneema has a low melting point of 140 ° C.
D LIFESPAN
The lifespan of the product is dependent on a number of factors, such as the manner and frequen-
cy of use, UV exposure, moisture, ice, affects of weather, storage conditions, and dirt
(sand, salt, etc.). Under extreme conditions the lifespan can be reduced to a single usage
or even less, if the equipment has suffered damage (for example during transport) before ever being used. Please
note: Products manufactured from synthetic fibres are subject to ageing even when not used. This ageing depends
mainly on environmental conditions as well as the impact of UV light.
Indications of the product's maximum lifespan:
Never: Correct storage: up to 10 years since production
Once or twice a year: up to 7 years
Once a month: up to 5 years
More times a month: up to 3 years
Every week: up to 1 year
Almost daily: up to 1/2 a year
The potential lifespan of metal products is unlimited, since the effective lifespan depends on the previously men-
tioned factors. Salewa recommends the replacing of products after maximum ten years.
E CLEANING, STORAGE, TRANSPORT AND SERVICING
See diagram E for guidelines on correct storage and care.
Do not allow this product to come into contact with aggressive chemicals (e. g. battery acid, solvents) or expose it
to extreme temperatures as these events can have a negative impact on the mechanical features of the materials.
Ensure that the product is kept safe during storage and transport and is protected from damage.
If necessary (eg. contact with dirt or salted water), wash the product in lukewarm water and and rinse with clear
water (max. 30°). Make sure that the product does not come into contact with chemicals. Leave to dry at room
temperature.
When they are worn out, replace them exclusively with new original components from Salewa.
F IDENTIFICATION LABELS
Carabiner
: Manufacturer's brand
xxxxxx: Product name
121: This confirms that the product has been manufactured in accordance with the UIAA requirements.
: Confirms adherence to the Regulation (EU) 2016/425
2008: Number of certifying body
Certification and control of control:
DOLOMITICERT S.C.A.R.L., Z.I. Villanova 7/A, 32013 Longarone (BL), Italy
0333: Number of certifying body
Certified by:
APAVE SUDEUROPE SAS, 8 rue Jean-Jacques Vernazza, Z.A.C. Saumaty-Séon, CS 60193, 13322, MARSEILLE CEDEX
16, France - Number of inspecting authority „0082"
Control of production by:
AFNOR Certification, 11 rue Francis de Pressensé 93571, 93571 La Plaine Saint-Denis Cedex France, France -
Number of inspecting authority „0333"
Made in xxxxx: Country of origin
x: Longitudinal breaking load in kN
x: Lateral breaking load in kN
x: Breaking load when open in kN
xxA mmyy: Information on traceability
xx: Index (Reference to current drawing)
A: Production batch
(A = first batch of the production month)
mm: Month of manufacture (01 = January)
yy: Year of manufacture (13 = 2013)
: Pictogramm indicating that the directions must be read.
Sling
: Name of supplier
EN566: The standard with which the product complies
2008: Certification and control of control: DOLOMITICERT S.C.A.R.L., Z.I. Villanova 7/A, 32013 Longarone (BL), Italy
Number of inspecting authority „2008"
0333: Certified by:
APAVE SUDEUROPE SAS, 8 rue Jean-Jacques Vernazza, Z.A.C. Saumaty-Séon, CS 60193, 13322, MARSEILLE CEDEX
16, France - Number of inspecting authority „0082"
Control of production by:
AFNOR Certification, 11 rue Francis de Pressensé 93571, 93571 La Plaine Saint-Denis Cedex France, France -
Nummer der Prüfstelle „0333"
Made in xxxxx: Country of origin
22kN: Breaking load in kN
xxA mmyy: Information on traceability
xx: Index (Reference to current drawing)
A: Production batch
(A = first batch of the production month)
mm: Month of manufacture (01 = January)
yy: Year of manufacture (13 = 2013)
SALEWA - Oberalp S.P.A., - Via Waltraud Gebert Deeg Strasse 4, I-39100 Bozen - Italy:
Brand, name and address of manufacturer