Atlas Copco QST62-350CT-T50-L202-H19 Bedienungsanleitung Seite 4

Safety Information
We, Atlas Copco Industrial Technique AB, cannot be held
liable for the consequences of using the declared values, in-
stead of values reflecting the actual exposure, in an individual
risk assessment in a work place situation over which we have
no control.
We recommend a programme of health surveillance to detect
early symptoms which may relate to noise exposure, so that
management procedures can be modified to help prevent fu-
ture impairment.
The noise emission is given as a guide to the machine-
builder. Noise emission data for the complete machine
should be given in the instruction manual for the ma-
chine.
WEEE
Information concerning Waste of Electrical and Electronic
Equipment (WEEE):
This product and its information, meets the requirements of
the WEEE Directive (2012/19/EU), and must be handled in
compliance with the directive.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and
a single black bar underneath, contain parts that must be han-
dled in compliance with the WEEE Directive. The entire
product, or the WEEE parts, can be sent to your "Customer
Center" for handling.
Other standards applied
QST/PST PowerMacs
EMC EN 61800-3:2004 +
A1:2012 Category C3
Electrical EN 61010-1:2010
Safety
EN 61010-2-201:2013
Information Regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
electrical and mechanical components in the product may
contain lead metal. This is in compliance with current sub-
stance restriction legislation and based on legit exemptions in
the RoHS Directive (2011/65/EU). Lead metal will not leak
or mutate from the product during normal use and the concen-
4
PF6 FlexSystem
EN 61000-6-2:2005
EN 61000-6-4:2007 +
A1:2011
EN 61326-1:2013
EN 61010-1:2010
EN 61010-2-201:2013
© Atlas Copco Industrial Technique AB - 9836 7023 00
QST62-350CT-T50-L202-H19
tration of lead metal in the complete product is well below the
applicable threshold limit. Please consider local requirements
on the disposal of lead at product end of life.
Regional Requirements
WARNING
This product can expose you to chemicals including lead,
which is known to the State of California to cause cancer
and birth defects or other reproductive harm. For more
information go to
https://www.p65warnings.ca.gov/
UK DECLARATION OF INCORPORATION
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsi-
bility that this product (with name, type and serial number,
see front page) fulfils the following essential requirements of
The Supply of Machinery (Safety) Regulations 2008 S.I.
2008/1597:
S.I. 2008/1597 (Annex I, clauses 1.1, 1.2 (excluding 1.2.4.3),
1.3, 1.4, 1.5, 1.6, 1.7)
And that this partly completed machinery is in conformity
with the provisions of the following other UK Regulation(s):
This partly completed machinery must not be put into service
until the final machinery into which it is to be incorporated
has been declared in conformity with provisions of The Sup-
ply of Machinery (Safety) Regulations 2008 S.I. 2008/1597,
where appropriate.
The following (parts/clauses of) Designated Standards have
been applied:
EN 61010-1 (2010) , EN 61800-3(2004) +A1(2012)
The relevant technical documentation was compiled and was
communicated in accordance with The Supply of Machinery
(Safety) Regulations 2008 S.I. 2008/1597 part B of Annex
VII. Authorities can request the technical file in electronic
form from:
Aleksandra Duric, Product Compliance Manager, Atlas
Copco Industrial Technique AB, SE-105 23 Stockholm Swe-
den
Stockholm, 1 September 2023
Håkan Andersson, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA