Scheppach HS81S Originalbetriebsanleitung Seite 22

(9) (fig. 5).
3. Now, screw the long centre brace (22) and the short
centre brace (21) onto the legs (9) using the hexa-
gon head bolts (20) and the hexagon head nuts (19).
Make sure that the same braces face each other.
The long centre braces (22) must be mounted
parallel to the operator's side of the saw. (Fig. 6).
4. Using two hex bolts (20) on each, loosely secure the
and hex nuts (19) at the drill holes of the rear sup-
port legs of the support frame (18) (fig. 7).
Attention!
Both support frames must be fastened to the
back of the machine!
5. Then, tighten all the nuts and bolts of the under-
frame.
Setting / mounting the riving knife (figs. 8-10)
m The setting Caution! Pull out the main plug!
The setting of the riving knife (6) must be checked
prior to commissioning. of the riving knife (6) must
be checked prior to commissioning.
1. Set the saw blade (3) to the max. cutting depth,
bring it to the 0° position and lock it.
2. Unfasten the bolt (23) from the bench insert (2) us-
ing a Phillips screwdriver, and remove bench insert
(22) (fig.8).
3. The distance between the saw blade (3) and the
riving knife (6) must be max. 5 mm. (Fig. 9)
4. Loosen the mounting bolt (24) in order to pull out
the splitting wedge (6) until the right distance is
adjusted (fig. 10).
5. Tighten the mounting screw (24) again and mount
the bench insert (2).
Mounting / dismounting the saw blade guard (figs.
11-12)
1. Place the saw blade guard (4) along with the bolt
(25) onto the riving knife (6) in a downwards direc-
tion so that the bolt sits firmly in the hole of the riving
knife (6).
2. Do not screw in the bolt (25) too tightly; the saw
blade guard (4) must move freely.
3. Plug the suction hose (5) onto the suction adapter
(26) and the connecting piece of the saw blade
guard (4). Connect a suitable splint collector onto
the suction adapter (26).
4. Disassembly is performed in reverse order.
Caution!
The saw blade guard (4) must be lowered onto
the workpiece before starting the sawing opera-
tion.
Replacing the bench insert (fig. 8)
1. In case of wear or damage, the bench insert (2)
must be replaced; otherwise, there is an increased
risk of injury.
2. Unfasten the bolt (23) using a Phillips screwdriver.
3. Take out the worn bench insert (2).
4. The installation of the new bench insert is done in
reverse order.
Installing / replacing the saw blade (fig. 13)
1. Caution! Pull out the main plug and wear safety
gloves.
2. Dismount the saw blade guard (4)
3. Remove the bench insert (2)
4. Loosen the nut by placing a saw blade spanner
(15b) on the nut while holding up another saw blade
spanner (15a) on the motor shaft.
5. Caution! Turn the nut in the direction of rotation of
the saw blade.
6. Remove the outer flange and remove the old blade
inner flange.
22 І 28 22 І 28
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58  www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
7. Clean the saw blade flange thoroughly with a wire
brush before mounting the new saw blade.
8. Insert the new saw blade in reverse order and
tighten.
Caution! Note the direction of run, the cutting
slope of the teeth must be in the direction of run,
i.e. facing forward.
9. Remount and adjust the bench insert (2) and saw
blade guard (4)
10. Before you start working again with the saw, check
proper functioning of the safety equipment.
Using the saw
On/Off switch (Fig. 14)
- The saw can be switched on by pressing the green
pushbutton „I". (10)
- The red pushbutton „0" (10) has to be pressed to
switch off the saw.
Overload protection (Fig. 14)
• This electrical power tool is provided with an overload
protection. In case that the overload protection was
initiated, proceed as follows:
• Disconnect the power tool from the power supply.
• Allow the power tool to cool down.
• Check the power tool carefully for possible damages.
• Have damages repaired before re-starting the power
tool.
• Connect the power tool to the power supply.
• Push the overload switch (27).
• Turn on the power tool as described and put it into
operation.
Cutting depth (Fig. 14)
Turn the round handle (11) to set the blade (3) to the
required cutting depth.
- Anticlockwise: smaller cutting depth
- Clockwise: larger cutting depth
After each new adjustment it is advisable to carry out a
trial cut in order to check the set dimensions.
Setting the angle (Fig. 14-15)
With the table saw you can make diagonal cuts to the
left oriented to the stop bar from 0 ° to 45 °.
m Check before each cut, that between the stop bar
(30), cross-stop (13) and the saw blade (5) a collision is
not possible.
- Undo the fixing handle (13).
- Set the desired angle on the scale by pressing and
turning the hand wheel (12).
- Lock the fixing handle (13) again in the required angle
position.
Working with the rip fence
Setting the stop height (figs. 15-16)
- The stop rail (30) of the rip fence (13) has two guide
surfaces with different heights.
- Depending on the thickness of the material to be cut,
the stop rail (30) as shown in fig. 16 must be used for
thick material (about 25 mm workpiece thickness) and
that shown in fig. 15 for thin material (less than 25 mm
workpiece thickness).
Turning the stop rail (figs. 15-16)
- Loosen the wing nuts (28) first for rotating the stop rail
(30).
- Now, the stop rail (30) can be removed from the guide
rail (29) and pushed over it again using the corre-