Kärcher K 4 Bedienungsanleitung Seite 13

Storage for spray lance
8
Transport handle
9
Hose reel
10
Storage for high-pressure gun
11
Wheel
12
Type plate
13
Clamp for connecting / disconnecting the high-pres-
14
sure hose
High-pressure hose
15
Clip for high-pressure hose
16
Fixing for high-pressure hose
17
Holder for hose reel
18
*Garden hose (fabric reinforced, diameter at least
19
1/2 inch (13 mm), length at least 7.5 m, with com-
mercially available quick coupling)
Water connection coupling
20
**KÄRCHER suction hose for water supply from
21
open containers (order no. 2.643-100)
Water connection with integrated sieve
22
Mains connection cable with mains plug
23
Screws
24
Detergent suction hose with detergent filter
25
Storage for high-pressure hose / mains connection
26
cable
* additionally required
** optionally available
Installation
For the illustrations, refer to the graphics page.
Fit the supplied loose parts onto the device before start-
ing up the device.
Have the included screws and the appropriate screw-
driver ready.
Mounting the transport handle
1. Attach the transport handle.
2. Secure the transport handle with 4 screws.
Illustration C
Mounting the storage option for the high-
pressure gun
1. Push in the storage option for the high-pressure gun
into the holder on the device.
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration D
Mounting the storage option for spray lances
1. Push in the storage option for the spray lances into
the holder on the device.
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration E
Mounting the storage option for the high-
pressure hose / mains connection cable
Devices without a hose reel
1. Push in the storage option for the high-pressure
hose / mains connection cable into the holder on the
transport handle.
2. Hold the storage option in the end position and se-
cure it using a screw.
Illustration F
Mounting the high-pressure hose reel
Devices with a hose reel
1. Attach the holder for the hose reel.
2. Secure the holder using 2 screws.
Illustration G
3. Attach the hose reel.
The hose reel locks into place.
Illustration H
Installing the water connection coupling
1. Screw the water connection coupling onto the water
connection on the device.
Illustration I
1. Place the device on a level, horizontal surface.
2. Unwind the high-pressure hose and eliminate any
loops and twists.
Note
Devices with a hose reel During operation, the high-
pressure hose must be completely unwound from the
hose reel.
3. Connect the high-pressure hose to the device.
a Pull up the clamp on the coupling.
b Insert the high-pressure hose into the coupling.
c Press down the clamp on the coupling.
Illustration J
4. Insert the high-pressure hose into the high-pressure
gun until it audibly latches into place.
Illustration K
Note
Take care to ensure the correct alignment of the nipple.
5. Check for a secure connection by pulling on the
high-pressure hose.
6. Plug the mains plug into a mains socket.
For the connection values, see the type plate or chapter
Technical data.
Observe the water distribution company regulations.
ATTENTION
Damage through contaminated water
Contamination in the water can damage the pump and
the accessories.
KÄRCHER recommends using the KÄRCHER water fil-
ter for protection(special accessory, order number
4.730-059).
Connection to the water line
ATTENTION
Hose coupling with Aquastop on the water connec-
tion of the device
Damage to the pump
Never use a hose coupling with Aquastop on the water
connection of the device.
You can use an Aquastop coupling on the tap.
1. Plug the garden hose onto the water connection
coupling.
English
Initial startup
Water supply
13