Teaching-In; Teaching-In Remote Controls And Buttons - HomeMatic HM-Sec-Key Montage- Und Bedienungsanleitung

Start-up
6.3

Teaching-in

Read this section entirely before starting to teach-in the device!
To integrate the door lock drive into your HomeMatic system and enable communication
with other HomeMatic devices (e.g. a HomeMatic Remote Control 4 buttons, KeyMatic),
the device has to be taught-in first. You can teach-in the device to other HomeMatic de-
vices (see sec. „6.3.1 Teaching-in remote controls and buttons" on page 42) or to the
HomeMatic Central Control Unit (see sec. „6.3.3 Teaching-in to the HomeMatic Central
Control Unit" on page 45).
6.3.1

Teaching-in remote controls and buttons

The first remote control that is taught-in is automatically defined as "Master"
remote control. Memory location "1" is reserved for this. This is required in
order to authenticate other teach-in procedures (from other buttons/button pairs
as well for the master remote control)!
Teach-in the first button pair of the Master remote control:
To teach-in a button pair to your door lock drive, proceed as follows:
Press the top button "Unlock" (D) for approx. 2 seconds, to start the teach-in procedure.
•
The display will show memory location "1". The symbols for radio reception and
"Unlock" flash; the door lock drive is ready for teaching-in.
Teach-in mode is ended automatically after teaching-in is successful, after
actuating any button on the drive or after 20 seconds without entry. A beep is
then emitted and "M" is shown on the display.
• Activate configuration mode of the remote control you wish to teach-in to the door
lock drive and briefly press one of the buttons of the button pair or respective button
to be taught-in. Please refer to the operating manual of the device you wish to teach-
in for further information on activating the teach-in mode.
Briefly pressing the button pair that has now been taught-in can be used for locking and
unlocking, a longer press of the "Unlock" button can be used for opening the door. This
first taught-in button pair is for authenticating further teach-in procedures.
Teaching-in an additional remote control/button pair
To teach-in an additional remote control or button pair to your door lock drive, proceed
as follows:
• Press the top button "Unlock" (D) for approx. 2 seconds, to start the teach-in procedure.
42
The LC display shows "X", the symbols for radio reception and "Unlock"
flash (aborting the teach-in procedure is possible as described above).
• Now, press any button on the "Master" remote control, that is already
assigned to the KeyMatic, until a free memory location is shown (e.g. "2".)
instead of "X".
The device LED of the master remote control is illuminated in red when
authenticating.
• In order to teach-in another button pair or a single button, set the remote control to
configuration mode and briefly press one of the buttons of the button pair or respec-
tive button to be taught-in. Please refer to the operating manual of the device you
wish to teach-in for further information on activating the teach-in mode.
Button pairs that are configured as "OFF/ON" buttons are taught-in with the
Lock/Unlock functions and a long press on the "ON" button will also open the
door.
To teach-in another remote control/button(pair), start again from the beginning.
The next free memory location appears (from 1-K). If there is no free memory
location, an error message ("FULL") appears on the LC display and the menu
is aborted. Up to 30 buttons on up to 20 different remote controls can be
taught-in. The memory location shown on the display of the door lock drive
symbolises a remote control. If more buttons(pairs) of a remote control have
been taught-in, this is also only shown with one memory location (for the
remote control).
We recommend that you mark the remote controls, e.g. write a number or a
letter inside the battery compartment cover.
If you pass the remote controls to a certain person, labelling remote control with
the assignment is a good idea (who has which remote control?). If lost, the right
remote control can be blocked simply and quickly (more precisely, the memory
location & the assignment of the remote control is deleted in the door lock
drive). The master remote control is recognized immediately when operating by
the "1" that appears on the KeyMatic display.
The "Master" remote control should not be given to anyone else, since only this
remove control can be used for registering or deleting other remote controls! If
the "Master" remote control is lost (or is defective), proceed according to sec.
„6.4.2 Replacing the master remote control" on page 47 to replace it.
Start-up
43