Vitek VT-1202 Red Bedienungsanleitung Seite 7

ENGLISH
−
Turn the regulator(9), set the desired tem-
perature of ironing: «•», «• •», «• • •» or
«MAX», depending on tissue type, when that
will be done, indicator will light (6).
− When the soleplate (13) warms up to the cho-
sen temperature and the indicator (6) goes
off, you can start ironing.
Note:
− When you turn on the iron for the first time,
the heating element of the iron burns, so you
may receive a small amount of smoke or a ex-
traneous smell, that is normal.
Water spray
− You can moisten the cloth, pressing several
times to spray button (5) (Fig. 2).
− Make sure that the tank (10)has enough wa-
ter.
Dry ironing
− Put the iron on the base (8).
− Plug the power cord into an outlet.
− Turn the regulator(9), set the desired tem-
perature of ironing: «•», «• •», «• • •» or
«MAX», depending on tissue type, with indi-
cator lights (6).
− Set the constant supply of steam (4) to «
position (steam off).
− When the soleplate is heated to the desired
temperature, the indicator (6) goes off, you
can start ironing.
− After use, set the iron temperature controller
(9) to position «MIN».
− Remove the plug from the wall outlet and wait
until iron get cool iron.
Steam ironing
Iron is equipped with a drip valve that shuts off
the water supply at very low temperature of the
soleplate, it prevents the droplets from the open-
ings of the soleplate (13). When the soleplate be
heating and cooling, you will hear a distinctive
clicking of opening / closing of stop valve, which
indicates its normal operation.
− Put the iron on the base (8).
− Plug the power cord into an outlet.
− Make sure that the tank (10) enough water.
− Turn the regulator(9) set the desired tem-
perature of ironing: in the work of area with
«MAX» steam the indicator lights (6).
1202.indd 6 1202.indd 6
− When the soleplate (13) is heated to the de-
sired temperature, the indicator (6) goes off,
you can start ironing.
− With the steam regulators (4) set the required
intensity of evaporation, steam will come out
of the hole soleplate (13) (Fig. 4).
− After the use, set the iron temperature con-
troller (9) to position «MIN», and the constant
control of steam (4) to «
− Remove the plug from the wall outlet and wait
until iron became cool.
WARNING!
If during operation there is no constant supply of
steam, make sure that the position of the regula-
tor of the steam is correct(4) and make sure you
have water in the tank.
Additional steam supply
Additional function of steam is useful for iron-
ing of wrinkles and can only be used with high
temperature ironing (temperature controller (9)
in «MAX» position).
When you press the steam button (3) intense
steam will come out of the soleplate.
Note:
− To avoid leakage of water from the steam
»
holes, press the button of additional steam
(3) with an interval of 4-5 seconds.
Vertical steaming
Vertical steam function can only be used in high
temperature ironing (temperature controller (9)
in «MAX» position).
Hold the iron vertically at a distance of 10-30 cm
from the garment and press the steam button (3)
with an interval of 4-5 seconds, the steam will rap-
idly get out of the soleplate holes (13) (Fig. 5).
Important information
− Do not perform a vertical steaming for syn-
thetic fabrics.
− When steaming, do not touch the material
with the soleplate to avoid melting.
− Never steam clothes, when it is on a person
because temperature of the steam is very
high, use a coat or clothes hanger.
− Once you've finished ironing, turn off the iron,
wait until it cools, then open the filler cap (2),
turn the iron and pour off excess water (Fig. 6).
6
» (steam off).
20.09.2011 12:34:57 20.09.2011 12:34:57