Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PAGE 8 OF 19
•
Offer the assembly into position as original while feeding the wires through the under-tray as original
and using the two shorter M6 button head bolts and washers (items 6 and 9) through the front
holes (the front of the motorcycle) from underneath, use two of the Nyloc nuts with washers (items
5 and 6) to secure in position as shown in pictures 17 and 18.
•
Tidy the wiring using the cable ties (item 16) provided.
•
Use the longer M6 button head bolt with washer (items 6 and 8) through the rear hole and secure
using the remaining nut and washer (items 5 and 6) to secure in position as shown in pictures 17
and 18.
•
Reconnect all the indicator wiring plugs or bullet connectors and check operation (if illumination fails,
swap the bullet connections around).
•
Connect the licence plate illuminator using the supplied connector (item 16) (if illumination fails,
swap the bullet connections around).
•
Fit licence plate to new licence plate bracket (it may require re-drilling).
IMPORTANT: IF FITTING A FULL-SIZE LICENCE PLATE AND PLACING IT FAR DOWN ON
THE LICENCE PLATE HANGER, THERE IS A SMALL CHANCE OF THE LICENCE PLATE
HITTING THE BACK WHEEL UNDER HEAVY LOAD AND OVER LARGE BUMPS IN THE ROAD.
IT IS YOUR RESPONSIBILITY TO CHECK FOR THIS POSSIBILITY AND TAKE AVOIDING
ACTION. FAILURE TO CHECK COULD RESULT IN SERIOUS INJURY.
•
Refit the tool holder/cable harness as original.
•
Refit the infill panel as original.
•
Refit both seats.
•
Depending on local laws, attach enclosed red reflector (item 13) in an appropriate location.
Please test the indicators, rear light and licence plate illuminator before riding.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill
and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for ensuring
that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified
or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if
the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting its liability for causing
death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability shall be limited to the
amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory
rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G. All returns are subject to a 25% restocking and handling fee (25% of the
gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No
returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not
refer to faulty goods.
Unit 1, Shelleys Lane, East Worldham, Alton, Hampshire GU34 3AQ.
Tel: +44 (0)1420 89007 Fax +44 (0)1420 87301
ISSUE 2 - 07/01/2020 (DM)
CONSUMER NOTICE
R&G RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
LP0282
Werbung
